• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

H3C MSR系列路由器典型配置举例(V5)-6W100

目录

63-MSR系列路由器模拟E&M无信令方式的典型组网和配置举例

本章节下载 63-MSR系列路由器模拟E&M无信令方式的典型组网和配置举例  (145.48 KB)

63-MSR系列路由器模拟E&M无信令方式的典型组网和配置举例

MSR系列路由器模拟E&M无信令模式典型配置举例

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H3C_彩色.emf

 



1  简介

本文档介绍模拟E&M无信令模式典型配置举例。

2  配置前提

本文档不严格与具体软、硬件版本对应,如果使用过程中与产品实际情况有差异,请参考相关产品手册,或以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证,配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置,为了保证配置效果,请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解E&M特性。

3  配置举例

3.1  组网需求

图1,Modem和路由器的模拟E&M卡相连,路由器配置E&M无信令模式。保持两侧Modem链路一直畅通,将信号采集器采集的数据实时发送到信号接收器上。

图1 模拟E&M无信令模式典型配置举例组网图

 

3.2  配置思路

·     为使双发可以建立呼叫,配置相关号码和实体;

·     配置E&M线路参数;

·     启动无信令模式,使设备发起呼叫。

3.3  使用版本

本举例是在Release 2104P02版本上进行配置和验证的。

3.4  配置步骤

3.4.1  RouterA的配置

<RouterA>system-view

[RouterA]interface GigabitEthernet 0/0

[RouterA-GigabitEthernet0/0]ip address 168.32.53.80 16

[RouterA-GigabitEthernet0/0]quit

[RouterA]voice-setup

[RouterA-voice]dial-program

# 配置IP呼叫所用的VoIP实体,匹配号码为“88..”。

[RouterA-voice-dial] entity 20 voip

[RouterA-voice-dial-entity20] match-template 88..

[RouterA-voice-dial-entity20] address sip ip 168.32.53.54

[RouterA-voice-dial-entity20] quit

# 配置E&M线路参数,假设和E&M连接的Modem中继线缆类型4线,中继信号类型为5类。

[RouterA] subscriber-line 5/0

[RouterA-subscriber-line5/0] em-phy-parm 4-wire

[RouterA-subscriber-line5/0] type 5

# 作为主叫网关,使能专线号码和E&M无信令模式,并启动监控时间为90秒

[RouterA-subscriber-line5/0]private-line 88

[RouterA-subscriber-line5/0]open-trunk caller monitor 90

3.4.2  RouterB的配置

<RouterB>system-view

[RouterB]interface GigabitEthernet 0/0

[RouterB-GigabitEthernet0/0]ip address 168.32.53.54 16

[RouterB-GigabitEthernet0/0]quit

[RouterB]voice-setup

[RouterB-voice]dial-program

# 配置E&M接口上的POTS语音实体。

[RouterB-voice-dial] entity 2000 pots

[RouterB-voice-dial-entity2000] match-template 8800

[RouterB-voice-dial-entity2000] line 6/0

[RouterB-voice-dial-entity2000] send-number all

# 配置E&M线路参数,假设和E&M连接的Modem中继线缆类型4线,中继信号类型为5类。

[RouterB] subscriber-line 6/0

[RouterB-subscriber-line6/0] em-phy-parm 4-wire

[RouterB-subscriber-line6/0] type 5

# 作为被叫网关,使能E&M无信令模式。

[RouterB-Subscriber-Line6/0]open-trunk called

3.5  验证配置

(1)     打开debug voice em all信息。使能open-trunk caller monitor 90命令后,可以看到主叫E&M设备立刻发起呼叫,与对方设备E&M建立连接,且链路建立成功后设备一直保持畅通状态。

*Sep 30 15:50:31:300 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: enable the open-trunk monitor, interval is configured 90s!,TimerId is 206

 

*Sep 30 15:50:31:300 2013 MSR5060 EM/7/VOICE:

 EM_EVENT : Called number is 8800!

 

*Sep 30 15:50:31:300 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Succeed in creating EMCCB.

 

*Sep 30 15:50:31:300 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Created message_wait TimerId [343] which will last 1000ms waiting for VIM_INSTALL_ACK.

 

*Sep 30 15:50:31:300 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Succeed in sending install to driver.

 

*Sep 30 15:50:31:301 2013 MSR5060 EM/7/VOICE:

 EM_FSM [5/0]: State changed from EM_IDLE to EMCALLED_WAIT_RECEIVE_NUMBER.

 

*Sep 30 15:50:31:321 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received VIM_INSTALL_ACK from VIM on state EMCALLED_WAIT_RECEIVE_NUMBER.

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Deleted TimerId [343].

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Private line number is: 8800.

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Begin to treat with Plar .

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: callernum=[],callednum=[8800]

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Succeed in sending AccpSetup to CMC.

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Created message_wait TimerId [969] which will last 3000ms waiting for AccpSetupAck.

 

*Sep 30 15:50:31:322 2013 MSR5060 EM/7/VOICE:

 EM_FSM [5/0]: State changed from EMCALLED_WAIT_RECEIVE_NUMBER to EMCALLED_WAIT_SETUP_ACK.

 

*Sep 30 15:50:31:324 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_SETUP_ACK from CMC on state EMCALLED_WAIT_SETUP_ACK.

 

*Sep 30 15:50:31:325 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Succeed in sending DTMFDetect off to Driver.

 

*Sep 30 15:50:31:325 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Deleted TimerId [969].

 

*Sep 30 15:50:31:325 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Created message_wait TimerId [606] which will last 40000ms waiting for AccpAlerting.

 

*Sep 30 15:50:31:325 2013 MSR5060 EM/7/VOICE:

 EM_FSM [5/0]: State changed from EMCALLED_WAIT_SETUP_ACK to EMCALLED_RINGING.

 

*Sep 30 15:50:31:326 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_SETUP_ACK from CMC on state EMCALLED_RINGING.

 

*Sep 30 15:50:31:326 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Deleted TimerId [606].

 

*Sep 30 15:50:31:326 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Created message_wait TimerId [169] which will last 40000ms waiting for AccpAlerting.

 

*Sep 30 15:50:31:326 2013 MSR5060 EM/7/VOICE:

 EM_FSM [5/0]: State changed from EMCALLED_RINGING to EMCALLED_RINGING.

 

*Sep 30 15:50:31:366 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_ALERTING from CMC on state EMCALLED_RINGING.

 

*Sep 30 15:50:31:367 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Deleted TimerId [169].

 

*Sep 30 15:50:31:367 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Succeed in sending AccpChannelReady to CMC.

 

*Sep 30 15:50:31:367 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Created message_wait TimerId [541] which will last 60000ms waiting for AccpConnect.

 

*Sep 30 15:50:31:367 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: E&M OpenTrunk do nothing

 

*Sep 30 15:50:31:368 2013 MSR5060 EM/7/VOICE:

 EM_EVENT : Received AccpChannelReadyAck Msg from CMC.

 

*Sep 30 15:50:37:577 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_CONNECT from CMC on state EMCALLED_RINGING.

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_TIMER [5/0]: Deleted TimerId [541].

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_FSM [5/0]: State changed from EMCALLED_RINGING to EMCALLED_TALKING.

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_INFORMATION from CMC on state EMCALLED_TALKING.

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Send to DRV [VICTL_COM_DTMF_DETECT_OFF].

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]: Received ACCP_INFORMATION from CMC on state EMCALLED_TALKING.

 

*Sep 30 15:50:37:578 2013 MSR5060 EM/7/VOICE:

 EM_EVENT [5/0]:Send to DRV [IOCTL_VOICE_NTE_ON],LocalPT=101,RemotePT=101.

(2)     呼叫建立后,设备每隔90s检测一次链路状态,如果发现链路没有处于畅通状态,那么会立刻发起呼叫再次建链。

*Sep 30 15:52:01:297 2013 MSR5060 EM/7/VOICE:

 EM_EVENT :Receive Em Timer Open Trunk monitor timer message,timerID = 206!

 

*Sep 30 15:52:01:297 2013 MSR50640 EM/7/VOICE:

 EM_EVENT: The current ViIndex has been Occupied.

 

*Sep 30 15:53:31:297 2013 MSR5060 EM/7/VOICE:

 EM_EVENT :Receive Em Timer Open Trunk monitor timer message,timerID = 206!

 

*Sep 30 15:53:31:297 2013 MSR5060 EM/7/VOICE:

 EM_EVENT: The current ViIndex has been Occupied.

3.6  配置文件

·     Router A

#         

version 5.20, Release 2104P02, Standard

#

 sysname RouterA

#

interface GigabitEthernet0/0

 port link-mode route

 ip address 168.32.53.80 255.255.0.0

#

voice-setup

 #

 sip

  #

 sip-server    

  #

  call-rule-set

  #

  call-route

 #

 dial-program

  #

entity 20 voip

   address sip ip 168.32.53.54

   match-template 88..

  #

 aaa-client

 #

 gk-client

#

subscriber-line5/0

private-line 88

open-trunk caller monitor 90

#

·     Router B

#

 sysname RouterB

#

interface GigabitEthernet0/0

 port link-mode route

 ip address 168.32.53.54 255.255.0.0

#

voice-setup

 #

 sip

  #

 sip-server    

  #

  call-rule-set

  #

  call-route

 #

 dial-program

 #

entity 2000 pots

   line 6/0

   send-number all

   match-template 8800

  #

subscriber-line6/0

 open-trunk called

#

4  相关资料

·     H3C MSR 系列路由器 命令参考(V5)-R2311

·     H3C MSR 系列路由器 配置指导(V5)-R2311

 

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们