Configuring LSI-9500 series storage controllers

	NOTE: The BIOS screens might vary by the BIOS version. The screenshots in this chapter are for illustration only.

 

About the LSI-9500 series storage controllers

The LSI-9500 series storage controllers support 12-Gbps data channels. For detailed storage controller information, access http://www.h3c.com/en/home/qr/default.htm?id=66.

The LSI-9500 series storage controllers contain the following models:

·     HBA-LSI-9500-8i

·     HBA-LSI-9500-16i

The storage controller does not support configuring RAID arrays.

Configuring controller settings in UEFI mode

This section describes how to configure the storage controller in UEFI mode. For more information about how to enter the BIOS and set the boot mode to UEFI, see the BIOS user guide for the server.

Controller configuration tasks at a glance

To configure controller settings in UEFI mode, perform the following tasks:

·     Refreshing configuration information

·     (Optional.) Viewing basic controller information

·     (Optional.) Viewing drive information

·     (Optional.) Locating drives

·     (Optional.) Configuring boot options for the legacy mode

Refreshing configuration information

1.     Access the BIOS setup screen. During server POST, press Delete, Esc, or F2 as prompted to open the BIOS setup screen as shown in Figure 1.

For how to navigate screens and modify settings, see the operation instructions at the lower right corner.

Figure 1 BIOS setup screen

 

2.     On the screen as shown in Figure 2, select Advanced > Storage controller, and press Enter. In this example, storage controller HBA 9500-8i is selected.

Figure 2 Advanced screen

 

3.     On the storage controller configuration screen as shown in Figure 3, select Refresh Topology and then press Enter.

Figure 3 Storage controller configuration screen

 

4.     On the confirmation screen as shown in Figure 4, select OK and then press Enter.

Figure 4 Confirming the operation

 

5.     On the screen as shown in Figure 5, select OK and then press Enter to return to the configuration screen.

Figure 5 Configuration completed

 

Viewing basic controller information

1.     Refresh configuration information. For more information, see "Refreshing configuration information."

2.     On the storage controller configuration screen as shown in Figure 6, select Controller Properties and then press Enter.

Figure 6 Storage controller configuration screen

 

3.     On the screen as shown in Figure 7, you can view basic information about the storage controller.

Figure 7 Basic controller information

 

Viewing drive information

1.     Refresh configuration information. For more information, see "Refreshing configuration information."

2.     On the screen as shown in Figure 8, select Device Properties and then press Enter.

Figure 8 Controller configuration screen

 

3.     On the storage controller configuration screen as shown in Figure 9, press Enter.

Figure 9 Selecting the enclosure

 

4.     On the screen as shown in Figure 10, select the target drive such as <Slot 4>SATA-SSD-ATA SAMSUNG MZ7L3480 and then press Enter.

Figure 10 Selecting the target drive

 

5.     On the drive configuration screen as shown in Figure 11, you can view information about the drive.

Figure 11 Drive properties screen

 

Locating drives

1.     On the drive properties screen as shown in Figure 12, select On from the drop-down list for the Locate LED option.

Figure 12 Drive properties screen

 

2.     Click Apply Changes.

Configuring boot options for the legacy mode

The storage controller does not provide legacy mode configuration screens. You can perform this task to configure boot options for the legacy mode in the UEFI BIOS. This enables users to install an OS in legacy mode.

To configure boot options for the legacy mode:

1.     On the drive properties screen as shown in Figure 13, select Yes in the drop-down list for the Legacy OpROM Boot Device option.

Figure 13 Drive properties screen

 

2.     Click Apply Changes.

Configuring controller settings in legacy mode

The storage controllers support the legacy mode but do not provide configuration screens in legacy mode.

Downloading and installing StorCLI

This section introduces the download and installation steps of the OS command line tool. You can use the OS command line tool to manage storage controllers during normal server operation without restarting the server.

Downloading StorCLI

1.     Access https://www.h3c.com/cn/BizPortal/DownLoadAccessory/DownLoadAccessoryFilt.aspx.

2.     Download the installation package and release notes for the corresponding storage controller firmware as instructed.

3.     Decompress the installation package to obtain the StorCLI tool package for different operating systems.

Installing StorCLI

See the release notes to install StorCLI for the corresponding operating system.

Commonly-used commands in StorCLI

This section describes the usage and examples of commonly used commands in StorCLI. You can use StorCLI commands to manage storage controllers during normal server operation without restarting the server.

 

IMPORTANT: All commands in StorCLI related to specifying paths do not support spaces or special characters.

 

Viewing the storage controller configuration

Perform this task to view storage controller information, including storage controller name, firmware version, drive slot, capacity, vendor, serial number, interface type, and interface speed.

Syntax

./storcli64 /ccontroller_id show

Parameters

controller_id: Specifies the controller ID. To view information about all storage controllers, specify the controller ID as all.

Examples

# View storage controller configuration.

[root@localhost storcli]# ./storcli64 /c0 show

CLI Version = 007.1207.0000.0000 Sep 25, 2019

Operating system = Linux 4.18.0-193.el8.x86_64

Controller = 0

Status = Success

Description = None

 

Product Name = HBA 9400-16i

Serial Number = SPB2726571

SAS Address =  500605b01193f2e0

PCI Address = 00:41:00:00

System Time = 03/21/2020 00:05:20

FW Package Build = 00.00.00.00

FW Version = 17.00.00.00

BIOS Version = 09.33.00.00_17.00.00.00

NVDATA Version = 17.01.00.25

PSOC Version = 06000001

Driver Name = mpt3sas

Driver Version = 32.100.00.00

Bus Number = 65

Device Number = 0

Function Number = 0

Vendor Id = 0x1000

Device Id = 0xAC

SubVendor Id = 0x1000

SubDevice Id = 0x3000

Board Name = HBA 9400-16i

Board Assembly = 03-50008-15011

Board Tracer Number = SPB2726571

Physical Drives = 7

 

PD LIST :

=======

 

----------------------------------------------------------------------------

EID:Slt DID State DG      Size Intf Med SED PI SeSz Model                Sp

----------------------------------------------------------------------------

7:0       0 JBOD  -  10.913 TB SATA HDD N   N  512B ST12000NM001G-2MV103 U

7:1       1 JBOD  -   7.277 TB SATA HDD N   N  512B HGST HUS728T8TALE6L4 U

7:2       2 JBOD  -   7.277 TB SATA HDD N   N  512B HGST HUS728T8TALE6L4 U

7:3       3 JBOD  -   7.277 TB SATA HDD N   N  512B HGST HUS728T8TALE6L4 U

7:4       4 JBOD  -  12.732 TB SATA HDD N   N  512B ST14000NM0018-2H4101 U

7:5       5 JBOD  -   7.277 TB SATA HDD N   N  512B HGST HUS728T8TALE6L4 U

7:12      6 JBOD  -   1.746 TB SATA SSD N   N  512B INTEL SSDSC2KB019T8  U

----------------------------------------------------------------------------

 

EID-Enclosure Device ID|Slt-Slot No.|DID-Device ID|DG-DriveGroup

UGood-Unconfigured Good|UBad-Unconfigured Bad|Intf-Interface

Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info

SeSz-Sector Size|Sp-Spun|U-Up|D-Down|T-Transition

 

Requested Boot Drive = Not Set

Upgrading the firmware of a storage controller

Perform this task to upgrade the firmware and BIOS driver of a storage controller.

Syntax

./storcli64 /ccontroller_id download file=x.bin

./storcli64 /ccontroller_id download bios file=x.rom

Parameters

controller_id: Specifies the controller ID.

x.bin: Specifies the name of the storage controller firmware.

x.rom: Specifies the BIOS driver of the storage controller.

Examples

# Upgrade a storage controller.

[root@localhost storcli]# ./storcli64 /c0 download

file=9500_8i_ Mixed_Profile_H3C.bin

'Downloading image.Please wait...

 

CLI Version = 007.2507.0000.0000 Feb 07, 2023

Operating system = Linux 5.14.0-70.22.1.el9_0.x86_64

Controller = 0

Status = Success

Description = Firmware Flash Successful

# Upgrade the BIOS driver of a storage controller.

[root@localhost storcli]# ./storcli64 /c0 download bios

file=IT_HBA_X64_BIOS_PKG_E6.rom

'Downloading image.Please wait...

 

CLI Version = 007.2507.0000.0000 Feb 07, 2023

Operating system = Linux 5.14.0-70.22.1.el9_0.x86_64

Controller = 0

Status = Success

Description = Bios Flash Successful

Managing drive UID LEDs

Perform this task to turn on or turn off the UID LED of a drive.

Syntax

./storcli64 /ccontroller_id /eenclosure_id /sslot_id operation locate

Parameters

controller_id: Specifies the controller ID.

enclosure_id: Specifies the enclosure ID. To manage the UID LEDs for drives in all enclosures, specify the enclosure ID as all.

slot_id: Specifies the ID of the physical drive slot. To manage the UID LEDs for all drives in the specified enclosure, specify the slot ID as all.

operation: Specifies the action to take.

·     start: Turn on the UID LED.

·     stop: Turn off the UID LED.

Examples

# Turn on the UID LED.

[root@localhost storcli]# ./storcli64 /c0/e7/s0 start locate

CLI Version = 007.1207.0000.0000 Sep 25, 2019

Operating system = Linux 4.18.0-193.el8.x86_64

Controller = 0

Status = Success

Description = Start Drive Locate Succeeded

# Turn off the UID LED.

[root@localhost storcli]# ./storcli64 /c0/e7/s0 stop locate

CLI Version = 007.1207.0000.0000 Sep 25, 2019

Operating system = Linux 4.18.0-193.el8.x86_64

Controller = 0

Status = Success

Description = Stop Drive Locate Succeeded

Upgrading the drive firmware

Perform this task to upgrade the drive firmware.

Syntax

./storcli64 /ccontroller_id /eenclosure_id/sslot_id download src=FW_name

Parameters

controller_id: Specifies the controller ID.

enclosure_id: Specifies the enclosure ID.

slot_id: Specifies the ID of the physical drive slot.

FW_name: Specifies the firmware name.

Examples

# Upgrade the drive firmware.

[root@localhost storcli]# ./storcli64 /c0/e7/s0 download src=Evans_SATA_5xxe_STD_OEM_SDnD_SN04.lod

Starting microcode update.please wait...

CLI Version = 007.1207.0000.0000 Sep 25, 2019

Operating system = Linux 4.18.0-193.el8.x86_64

Controller = 0

Status = Success

Description = None

Troubleshooting

For detailed information about collecting storage controller fault information, diagnosing and locating faults, and troubleshooting servers, see H3C Servers Troubleshooting Guide.

Compatibility

For information about storage controller and server compatibility, access http://www.h3c.com/en/home/qr/default.htm?id=66.

Downloading and installing drivers

Access https://www.h3c.com/en/Support/Resource_Center/EN/Severs/Catalog/Optional_Parts/Storage_Controller/?tbox=Software to download the storage controller drivers. For more information about installing drivers, see the release notes for the driver program.