Configuring IPv6 IS-IS· 1

Overview·· 1

Configuring basic IPv6 IS-IS· 1

Configuring IPv6 IS-IS route control 2

Configuring BFD for IPv6 IS-IS· 3

Displaying and maintaining IPv6 IS-IS· 3

IPv6 IS-IS configuration examples 3

IPv6 IS-IS basic configuration example· 3

BFD for IPv6 IS-IS configuration example· 8

 

IPv6 IS-IS supports all IPv4 IS-IS features except that it advertises IPv6 routing information. This chapter describes only IPv6 IS-IS specific configuration tasks. For information about IS-IS, see "Configuring IS-IS."

Overview

Intermediate System-to-Intermediate System (IS-IS) supports multiple network protocols, including IPv6. To support IPv6, the IETF added two type-length-values (TLVs) and a new network layer protocol identifier (NLPID).

The TLVs are as follows:

·           IPv6 Reachability—Contains routing prefix and metric information to describe network reachability and has a type value of 236 (0xEC).

·           IPv6 Interface Address—Same as the "IP Interface Address" TLV in IPv4 ISIS, except that the 32-bit IPv4 address is translated to the 128-bit IPv6 address.

The new NLPID is an 8-bit field that identifies which network layer protocol is supported. For IPv6, the NLPID is 142 (0x8E), which must be carried in hello packets sent by IPv6 IS-IS.

Configuring basic IPv6 IS-IS

Before you configure basic IPv6 IS-IS, complete the following tasks:

·           Configure IPv6 addresses for interfaces to ensure IPv6 connectivity between neighboring nodes.

·           Enable IS-IS.

Basic IPv6 IS-IS configuration can implement the interconnection of IPv6 networks.

To configure basic IPv6 IS-IS:

 

Step	Command	Remarks
1.     Enter system view.	system-view	N/A
2.     Enable an IS-IS process and enter IS-IS view.	isis [ process-id ] [ vpn-instance vpn-instance-name ]	By default, no IS-IS process is enabled.
3.     Configure the network entity title (NET) for the IS-IS process.	network-entity net	By default, no NET is configured.
4.     Enable IPv6 for the IS-IS process.	ipv6 enable	The default setting is disabled.
5.     Return to system view.	quit	N/A
6.     Enter interface view.	interface interface-type interface-number	N/A
7.     Enable IPv6 for an IS-IS process on the interface.	isis ipv6 enable [ process-id ]	The default setting is disabled.

 

Configuring IPv6 IS-IS route control

Before you configure IPv6 IS-IS route control, complete basic IPv6 IS-IS configuration.

To configure IPv6 IS-IS route control:

 

Step	Command	Remarks
1.     Enter system view.	system-view	N/A
2.     Enter IS-IS view.	isis [ process-id ] [ vpn-instance vpn-instance-name ]	N/A
3.     Specify a preference for IPv6 IS-IS routes.	ipv6 preference { route-policy route-policy-name | preference } *	By default, the default setting is 15.
4.     Configure an IPv6 IS-IS summary route.	ipv6 summary ipv6-prefix prefix-length [ avoid-feedback | generate_null0_route | [ level-1 | level-1-2 | level-2 ] | tag tag ] *	By default, no IPv6 IS-IS summary route is configured.
5.     Generate an IPv6 IS-IS default route.	ipv6 default-route-advertise [ [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name ] *	By default, no IPv6 default route is generated.
6.     Configure IPv6 IS-IS to filter redistributed routes.	ipv6 filter-policy { acl6-number | prefix-list prefix-list-name | route-policy route-policy-name } export [ protocol [ process-id ] ]	By default, IPv6 IS-IS does not filter redistributed routes. This command is usually used together with the ipv6 import-route command.
7.     Configure IPv6 IS-IS to filter inbound routes.	ipv6 filter-policy { acl6-number | prefix-list prefix-list-name | route-policy route-policy-name } import	By default, IPv6 IS-IS does not filter inbound routes.
8.     Configure IPv6 IS-IS to redistribute routes from another routing protocol.	ipv6 import-route protocol [ process-id ] [ allow-ibgp ] [ cost cost | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *	By default, IPv6 IS-IS does not redistribute routes from any other routing protocol.
9.     Configure the maximum number of redistributed Level 1/Level 2 IPv6 routes.	ipv6 import-route limit number	By default, the maximum number of redistributed Level 1/Level 2 IPv6 routes is 131072.
10.   Configure route advertisement from Level-2 to Level-1.	ipv6 import-route isisv6 level-2 into level-1 [ filter-policy { acl6-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *	By default, IPv6 IS-IS does not advertise routes from Level-2 to Level-1.
11.   Configure route advertisement from Level-1 to Level-2.	ipv6 import-route isisv6 level-1 into level-2 [ filter-policy { acl6-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *	By default, IPv6 IS-IS advertises routes from Level-1 to Level-2.
12.   Specify the maximum number of ECMP routes for load balancing.	ipv6 maximum load-balancing number	By default, the maximum number of ECMP routes is 32.

 

Configuring BFD for IPv6 IS-IS   

Bidirectional forwarding detection (BFD) can quickly detect faults between IPv6 IS-IS neighbors to improve the convergence speed of IPv6 IS-IS. For more information about BFD, see High Availability Configuration Guide.

To configure BFD for IPv6 IS-IS:

 

Step	Command	Remarks
1.     Enter system view.	system-view	N/A
2.     Enable an IS-IS process and enter IS-IS view.	isis [ process-id ] [ vpn-instance vpn-instance-name ]	N/A
3.     Configure the NET for the IS-IS process.	network-entity net	By default, no NET is configured.
4.     Enable IPv6 for the IS-IS process.	ipv6 enable	By default, IPv6 for the IS-IS process is disabled.
5.     Return to system view.	quit	N/A
6.     Enter interface view.	interface interface-type interface-number	N/A
7.     Enable IPv6 for an IS-IS process.	isis ipv6 enable [ process-id ]	By default, IPv6 is disabled for an IS-IS process.
8.     Enable BFD for IPv6 IS-IS.	isis ipv6 bfd enable	By default, BFD for IPv6 IS-IS is disabled.

 

Displaying and maintaining IPv6 IS-IS   

Execute display commands in any view. For other display and reset commands, see "Configuring IS-IS."

 

Task	Command
Display information about routes redistributed by IPv6 IS-IS.	display isis redistribute ipv6 [ ipv6-address mask-length ] [ level-1 | level-2 ] [ process-id ]
Display IPv6 IS-IS routing information.	display isis route ipv6 [ ipv6-address ] [ [ level-1 | level-2 ] | verbose ] * [ process-id ]

 

IPv6 IS-IS configuration examples

By default, Ethernet, VLAN, and aggregate interfaces are down. To configure such an interface, bring the interface up by executing the undo shutdown command.

IPv6 IS-IS basic configuration example

Network requirements

As shown in Figure 1, Switch A, Switch B, Switch C, and Switch D, all enabled with IPv6, reside in the same AS. Configure IPv6 IS-IS on the switches so that they can reach each other.

Switch A and Switch B are Level-1 switches, Switch D is a Level-2 switch, and Switch C is a Level-1-2 switch.

Figure 1 Network diagram

 

Configuration procedure

1.      Configure IPv6 addresses for interfaces. (Details not shown.)

2.      Configure IPv6 IS-IS:

# Configure Switch A.

<SwitchA> system-view

[SwitchA] isis 1

[SwitchA-isis-1] is-level level-1

[SwitchA-isis-1] network-entity 10.0000.0000.0001.00

[SwitchA-isis-1] ipv6 enable

[SwitchA-isis-1] quit

[SwitchA] interface vlan-interface 100

[SwitchA-Vlan-interface100] isis ipv6 enable 1

[SwitchA-Vlan-interface100] quit

# Configure Switch B.

<SwitchB> system-view

[SwitchB] isis 1

[SwitchB-isis-1] is-level level-1

[SwitchB-isis-1] network-entity 10.0000.0000.0002.00

[SwitchB-isis-1] ipv6 enable

[SwitchB-isis-1] quit

[SwitchB] interface vlan-interface 200

[SwitchB-Vlan-interface200] isis ipv6 enable 1

[SwitchB-Vlan-interface200] quit

# Configure Switch C.

<SwitchC> system-view

[SwitchC] isis 1

[SwitchC-isis-1] network-entity 10.0000.0000.0003.00

[SwitchC-isis-1] ipv6 enable

[SwitchC-isis-1] quit

[SwitchC] interface vlan-interface 100

[SwitchC-Vlan-interface100] isis ipv6 enable 1

[SwitchC-Vlan-interface100] quit

[SwitchC] interface vlan-interface 200

[SwitchC-Vlan-interface200] isis ipv6 enable 1

[SwitchC-Vlan-interface200] quit

[SwitchC] interface vlan-interface 300

[SwitchC-Vlan-interface300] isis ipv6 enable 1

[SwitchC-Vlan-interface300] quit

# Configure Switch D.

<SwitchD> system-view

[SwitchD] isis 1

[SwitchD-isis-1] is-level level-2

[SwitchD-isis-1] network-entity 20.0000.0000.0004.00

[SwitchD-isis-1] ipv6 enable

[SwitchD-isis-1] quit

[SwitchD] interface vlan-interface 300

[SwitchD-Vlan-interface300] isis ipv6 enable 1

[SwitchD-Vlan-interface300] quit

[SwitchD] interface vlan-interface 301

[SwitchD-Vlan-interface301] isis ipv6 enable 1

[SwitchD-Vlan-interface301] quit

Verifying the configuration

# Display the IPv6 IS-IS routing table on Switch A.

[SwitchA] display isis route ipv6

 

                         Route information for IS-IS(1)

                         ------------------------------

 

                         Level-1 IPv6 Forwarding Table

                         -----------------------------

 

 Destination : ::                                      PrefixLen: 0

 Flag        : R/-/-                                   Cost     : 10

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan100

 

 Destination : 2001:1::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan100

 

 Destination : 2001:2::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan100

 

 Destination : 2001:3::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan100

 

      Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

# Display the IPv6 IS-IS routing table on Switch B.

[SwitchB] display isis route ipv6

 

                         Route information for IS-IS(1)

                         ------------------------------

 

                         Level-1 IPv6 Forwarding Table

                         -----------------------------

 

 Destination : ::                                      PrefixLen: 0

 Flag        : R/-/-                                   Cost     : 10

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan200

 

 Destination : 2001:1::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan200

 

 Destination : 2001:2::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : Direct                                  Interface: Vlan200

 

 Destination : 2001:3::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan200

 

      Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

# Display the IPv6 IS-IS routing table on Switch C.

[SwitchC] display isis route ipv6

 

                         Route information for IS-IS(1)

                         ------------------------------

 

                         Level-1 IPv6 Forwarding Table

                         -----------------------------

 

 Destination : 2001:1::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan100

 

 Destination : 2001:2::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan200

 

 Destination : 2001:3::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan300

 

      Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

 

                         Level-2 IPv6 Forwarding Table

                         -----------------------------

 

 Destination : 2001:1::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan100

 

 Destination : 2001:2::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan200

 

 Destination : 2001:3::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan300

 

 Destination : 2001:4::1                               PrefixLen: 128

 Flag        : R/-/-                                   Cost     : 10

 Next Hop    : FE80::20F:E2FF:FE3E:FA3D                Interface: Vlan300

 

      Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

# Display the IPv6 IS-IS routing table on Switch D.

[SwitchD] display isis route ipv6

 

                         Route information for IS-IS(1)

                         ------------------------------

 

                         Level-2 IPv6 Forwarding Table

                         -----------------------------

 

 Destination : 2001:1::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan300

 

 Destination : 2001:2::                                PrefixLen: 64

 Flag        : R/-/-                                   Cost     : 20

 Next Hop    : FE80::200:FF:FE0F:4                     Interface: Vlan300

 

 Destination : 2001:3::                                PrefixLen: 64

 Flag        : D/L/-                                   Cost     : 10

 Next Hop    : Direct                                  Interface: Vlan300

 

 Destination : 2001:4::1                               PrefixLen: 128

 Flag        : D/L/-                                   Cost     : 0

 Next Hop    : Direct                                  Interface: Loop1

 

      Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

BFD for IPv6 IS-IS configuration example

Network requirements

·           As shown in Figure 2, configure IPv6 IS-IS on Switch A and Switch B so that they can reach other.

·           Enable BFD on VLAN-interface 10 of Switch A and Switch B. After the link between Switch B and the Layer-2 switch fails, BFD can quickly detect the failure and notify IPv6 IS-IS of the failure. Then Switch A and Switch B communicate through Switch C.

Figure 2 Network diagram

 

Device	Interface	IPv6 address	Device	Interface	IPv6 address
Switch A	Vlan-int10	2001::1/64	Switch B	Vlan-int10	2001::2/64
	Vlan-int11	2001:2::1/64		Vlan-int13	2001:3::2/64
Switch C	Vlan-int11	2001:2::2/64
	Vlan-int13	2001:3::1/64

 

Configuration procedure

1.      Configure IP addresses for interfaces. (Details not shown.)

2.      Configure IPv6 IS-IS:

# Configure Switch A.

<SwitchA> system-view

[SwitchA] isis 1

[SwitchA-isis-1] is-level level-1

[SwitchA-isis-1] network-entity 10.0000.0000.0001.00

[SwitchA-isis-1] ipv6 enable

[SwitchA-isis-1] quit

[SwitchA] interface vlan-interface 10

[SwitchA-Vlan-interface10] isis ipv6 enable 1

[SwitchA-Vlan-interface10] quit

[SwitchA] interface vlan-interface 11

[SwitchA-Vlan-interface11] isis ipv6 enable 1

[SwitchA-Vlan-interface11] quit

# Configure Switch B.

<SwitchB> system-view

[SwitchB] isis 1

[SwitchB-isis-1] is-level level-1

[SwitchB-isis-1] network-entity 10.0000.0000.0002.00

[SwitchB-isis-1] ipv6 enable

[SwitchB-isis-1] quit

[SwitchB] interface vlan-interface 10

[SwitchB-Vlan-interface10] isis ipv6 enable 1

[SwitchB-Vlan-interface10] quit

[SwitchB] interface vlan-interface 13

[SwitchB-Vlan-interface13] isis ipv6 enable 1

[SwitchB-Vlan-interface13] quit

# Configure Switch C.

<SwitchC> system-view

[SwitchC] isis 1

[SwitchC-isis-1] network-entity 10.0000.0000.0003.00

[SwitchC-isis-1] ipv6 enable

[SwitchC-isis-1] quit

[SwitchC] interface vlan-interface 11

[SwitchC-Vlan-interface11] isis ipv6 enable 1

[SwitchC-Vlan-interface11] quit

[SwitchC] interface vlan-interface 13

[SwitchC-Vlan-interface13] isis ipv6 enable 1

[SwitchC-Vlan-interface13] quit

3.      Configure BFD functions:

# Enable BFD and configure BFD parameters on Switch A.

[SwitchA] bfd session init-mode active

[SwitchA] interface vlan-interface 10

[SwitchA-Vlan-interface10] isis ipv6 bfd enable

[SwitchA-Vlan-interface10] bfd min-transmit-interval 500

[SwitchA-Vlan-interface10] bfd min-receive-interval 500

[SwitchA-Vlan-interface10] bfd detect-multiplier 7

[SwitchA-Vlan-interface10] return

# Enable BFD and configure BFD parameters on Switch B.

[SwitchB] bfd session init-mode active

[SwitchB] interface vlan-interface 10

[SwitchB-Vlan-interface10] isis ipv6 bfd enable

[SwitchB-Vlan-interface10] bfd min-transmit-interval 500

[SwitchB-Vlan-interface10] bfd min-receive-interval 500

[SwitchB-Vlan-interface10] bfd detect-multiplier 6

Verifying the configuration

# Display BFD session information on Switch A.

<SwitchA> display bfd session

 

 Total Session Num: 1            Init Mode: Active

 

 IPv6 Session Working Under Ctrl Mode:

 

     Local Discr: 1441                Remote Discr: 1450

       Source IP: FE80::20F:FF:FE00:1202 (link-local address of VLAN-interface 10 on Switch A)

  Destination IP: FE80::20F:FF:FE00:1200 (link-local address of VLAN-interface 10 on Switch B)

   Session State: Up                     Interface: Vlan10

       Hold Time: 2319ms

# Display routes destined for 2001:4::0/64 on Switch A.

<SwitchA> display ipv6 routing-table 2001:4::0 64

 

Summary Count : 1

 

Destination: 2001:4::/64                                 Protocol  : ISISv6

NextHop    : FE80::20F:FF:FE00:1200                      Preference: 15

Interface  : Vlan10                                      Cost      : 10

The output shows that Switch A and Switch B communicate through VLAN-interface 10. Then the link over VLAN-interface 10 fails.

# Display routes destined for 2001:4::0/64 on Switch A.

<SwitchA> display ipv6 routing-table 2001:4::0 64

 

Summary Count : 1

 

Destination: 2001:4::/64                                 Protocol  : ISISv6

NextHop    : FE80::BAAF:67FF:FE27:DCD0                   Preference: 15

Interface  : Vlan11                                      Cost      : 20

The output shows that Switch A and Switch B communicate through VLAN-interface 11.