Contents

SRPM commands· 1

activate profile· 1

delay-profile link-based· 1

display srpm delay-profile· 2

display srpm delay-statistics· 3

display srpm interface· 4

dscp· 6

interval 7

protocol 8

reset srpm delay-statistics· 9

srpm·· 9

srpm delay-profile link-based query enable· 10

srpm delay-profile link-based response enable· 10

srpm destination· 11

udp destination-port 12

udp source-port 13

 

SRPM commands

activate profile

Use activate profile to activate a link-based delay profile.

Use undo activate profile to deactivate a link-based delay profile.

Syntax

activate profile

undo activate profile

Default

A link-based delay profile is not activated.

Views

Link-based delay profile view

Predefined user roles

network-admin

Usage guidelines

After creating or modifying a delay profile, you must activate the profile for the new configuration to take effect.

Reactivating a delay profile clears history measurement statistics on SRPM-enabled interfaces that are associated with this delay profile. The interfaces will use the new configuration to start new measurement sessions.

Before modifying parameters in a delay profile or terminating measurement sessions related to that profile, you must use the undo activate profile command to deactivate that profile.

Examples

# Activate the link-based delay profile named test.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] activate profile

delay-profile link-based

Use delay-profile link-based to create a link-based delay profile and enter its view, or enter the view of an existing link-based delay profile.

Use undo delay-profile link-based to delete a link-based delay profile.

Syntax

delay-profile link-based profile-name

undo delay-profile link-based profile-name

Default

No link-based delay profiles exist.

Views

SRPM view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a profile name, a case-sensitive string of 1 to 31 characters. The name can contain only letters, digits, and underscores.

Usage guidelines

Deleting a profile stops all measurements related to that profile and deletes all settings in the view of that profile and all settings related to that profile in interface view.

Examples

# Create a link-based delay profile named test and enter its view.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test]

display srpm delay-profile

Use display srpm delay-profile to display information about SRPM delay profiles.

Syntax

display srpm delay-profile { brief | link-based [ profile-name ] }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

brief: Displays brief information about all delay profiles.

link-based: Displays detailed information about link-based delay profiles.

profile-name: Specifies a delay profile by its name, a case-sensitive string of 1 to 31 characters. The name can contain only letters, digits, and underscores (_). If you do not specify a delay profile, this command displays detailed information about all link-based delay profiles.

Examples

# Display brief information about all delay profiles.

<Sysname> display srpm delay-profile brief

Number of profiles: 2

 

Name                            Type           Status             Sessions

Test1                           Link-based     Activated          2

Test2                           Link-based     Inactivated        0

# Display detailed information about all link-based delay profiles.

<Sysname> display srpm delay-profile link-based

Number of profiles: 1

 

Link-based delay profile: test

  Profile configuration:

    Status             : Activated

    Protocol           : udp

    Destination port   : 8000

    Source port        : 9000

    Interval           : 30 sec

    DSCP               : 4

    Mode               : two-way

  Profile application:

    Measured links     : 2

    Measured sessions  : 2

Table 1 Command output

Field	Description
Name	Profile name.
Type	SRPM measurement type. The value is Link-based.
Status	Whether the profile has been activated: ·     Activated. ·     Inactivated.
Sessions	Number of measurement sessions that use the profile.
Link-based delay profile	Name of the link-based delay profile.
Profile configuration	Profile configuration information.
Protocol	Encapsulation method used by SRPM packets. To configure the encapsulation method, use the protocol command.
Destination port	Destination UDP port number in measurement packets.
Source port	Source UDP port number in measurement packets.
Interval	Measurement packet sending interval, in seconds.
DSCP	DSCP value in measurement packets.
Mode	Measurement mode. Value two-way represents two-way measurement.
Profile application	Profile application statistics.
Measured links	Number of links being measured by using the current profile.
Measured sessions	Number of sessions being measured by using the current profile.

 

display srpm delay-statistics

Use display srpm delay-statistics to display SRPM delay measurement statistics.

Syntax

display srpm delay-statistics [ interface interface-type interface-number ] [ number number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays delay measurement statistics for all interfaces.

number number: Displays the specified number of most recent delay measurement statistics. The value range for the number argument is 1 to 64. The default value is 5.

Examples

# Display the most recent five SRPM delay measurement statistics on all interfaces.

<Sysname> display srpm delay-statistics

Latest two-way delay statistics (us) for Ten-GigabitEthernet3/0/1:

Index          Delay                Jitter

12             41001                -

13             100001               59000

14             94001                6000

15             95001                1000

16             161001               66000

Average delay: 98201                Average jitter: 33000

Maximum delay: 161001               Maximum jitter: 66000

Minimum delay: 41001                Minimum jitter: 1000

Table 2 Command output

Field	Description
Latest two-way delay statistics (us) for Ten-GigabitEthernet3/0/1	Latest two-way delay measurement statistics for the links attached to the interface. The unit is microsecond.
Index	Index number of statistics.
Delay	Two-way delay value measured by SRPM, in microsegment.
Jitter	Jitter value, which is the absolute value for the difference between the delay values measured in two consecutive rounds.
Average delay	Average delay value measured by SRPM.
Average jitter	Average jitter value measured by SRPM.
Maximum delay	Maximum delay value measured by SRPM.
Maximum jitter	Maximum jitter value measured by SRPM.
Minimum delay	Minimum delay value measured by SRPM.
Minimum jitter	Minimum jitter value measured by SRPM.

 

display srpm interface

Use display srpm interface to display interface-specific SRPM information.

Syntax

display srpm interface interface-type interface-number

display srpm interface [ interface-type interface-number ] brief

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays SRPM information on all interfaces.

brief: Displays brief interface-specific SRPM information. If you do not specify this keyword, the command displays detailed interface-specific SRPM information.

Examples

# Display brief interface-specific SRPM information.

<Sysname> display srpm interface brief

Interface        Link-based delay-profile        Status

XGE3/0/1         test                            Response enabled

XGE3/0/2         test2                           Query enabled

# Display detailed SRPM information on interface Ten-GigabitEthernet 3/0/1.

<Sysname> display srpm interface ten-gigabitethernet 3/0/1

Link-based delay measurement:

  Link-based delay-profile    : test

  Status                      : Response enabled

  Measurement status          : Measuring

  Local IP address            : 1.1.1.1

  Destination IPv4 address    : 1.1.1.2

  Destination IPv6 address    : 1::2

  Local MAC address           : 0001-0001-0001

  Start time                  : 2020-03-31 11:40:45.31

  End time                    : -

  Counters:

    Session ID                : 1

    Packets:

      Sent                    : 855220

      Received                : 855220

      Sent errors             : 0

      Received errors         : 0

Table 3 Command output

Field	Description
Link-based delay measurement	Information about link-based delay measurement.
Link-based delay-profile	Name of the link-based delay profile.
Status	SRPM status on the interface: ·     Response enabled—SRPM response is enabled. ·     Query enabled—SRPM query is enabled.
Measurement status	Measurement status of the delay profile: ·     Measuring. ·     Not measuring (reason)—For more information about the reason, see Table 4.
Local IP address	Local IPv4 or IPv6 address of the interface.
Destination IPv4 address	Destination IPv4 address of the interface.
Destination IPv6 address	Destination IPv6 address of the interface.
Local MAC address	Local MAC address.
Start time	Time when the measurement started.
End time	Time when the measurement finished.
Counters	Counter statistics.
Session ID	SRPM session ID.
Packets	Packet statistics.
Sent	Total number of packets sent by the interface.
Received	Total number of packets received by the interface.
Sent errors	Total number of error packets sent by the interface.
Received errors	Total number of error packets received by the interface.

 

Table 4 Reasons for profile deactivation

Reason	Description
Profile inactivated	The profile is not activated.
This interface is an aggregate member port	The interface is a member port of an aggregate interface.
Invalid source IP	The source IP address is invalid.
Destination IP unreachable	The destination IP address is unreachable.
Line protocol down	The link layer protocol is in down state on the interface.
Internet protocol down	The network layer protocol is in down state on the interface. Typically, this issue is caused because no IP address is configured for the interface.
Entry is not ready	SRPM entry is not ready.
Failed to set the entry	Failed to set the SRPM entry.

 

dscp

Use dscp to specify a DSCP value for SRPM request packets.

Use undo dscp to restore the default.

Syntax

dscp dscp-value

undo dscp

Default

The DSCP value is 0 for SRPM request packets.

Views

Link-based delay profile view

Predefined user roles

network-admin

Parameters

dscp-value: Specifies a DSCP value in the range of 0 to 63.

Usage guidelines

DSCP determines packet transmission priority. The higher the DSCP value, the higher the transmission priority.

Use this command only when the delay profile is deactivated.

Examples

# In delay profile test, set the DSCP value to 3 for SRPM request packets.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] dscp 3

Related commands

activate profile

interval

Use interval to set the interval for sending SRPM request packets.

Use undo interval to restore the default.

Syntax

interval interval-value

undo interval

Default

SRPM request packets are sent at intervals of 30 seconds.

Views

Link-based delay profile view

Predefined user roles

network-admin

Parameters

interval-value: Sets the interval for sending SRPM request packets, in the range of 1 to 3600 seconds.

Usage guidelines

Use this command only when the delay profile is deactivated.

Examples

# Set the interval to 60 seconds for sending SRPM request packets.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] interval 60

Related commands

activate profile

protocol

Use protocol to specify an encapsulation method for SRPM packets.

Use undo protocol to restore the default.

Syntax

protocol { mpls | udp | udpv6 }

undo protocol

Default

By default, UDP encapsulation is used for SRPM packets.

Views

Link-based delay profile view

Predefined user roles

network-admin

Parameters

mpls: Specifies MPLS encapsulation.

udp: Specifies UDP encapsulation.

udpv6: Specifies UDPv6 encapsulation.

Usage guidelines

SRPM packets support the following encapsulation methods:

·     MPLS encapsulation—MPLS is used to encapsulate SRPM packets.

·     UDP encapsulation—UDP is used to encapsulate SRPM packets. The source and destination IP addresses in the IP header are IPv4 addresses.

·     UDPv6 encapsulation—UDP is used to encapsulate SRPM packets. The source and destination IP addresses in the IP header are IPv6 addresses.

Use this command only when the delay profile is deactivated.

Examples

# Set the encapsulation method to UDP for SRPM packets.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] protocol udp

Related commands

activate profile

reset srpm delay-statistics

Use reset srpm delay-statistics to clear statistics about SRPM delay measurement.

Syntax

reset srpm delay-statistics interface interface-type interface-number

Views

User view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number.

Examples

# Clear delay measurement statistics on interface Ten-GigabitEthernet 3/0/1.

<Sysname> reset srpm delay-statistics interface ten-gigabitethernet 3/0/1

Related commands

display srpm delay-statistics

srpm

Use srpm to enable SRPM and enter SRPM view.

Use undo srpm to disable SRPM.

Syntax

srpm

undo srpm

Default

SRPM is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Execution of the undo srpm command stops all SRPM measurements and deletes all SRPM settings including the SRPM settings in SRPM view and interface view.

Examples

# Enable SRPM and enter SRPM view.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm]

srpm delay-profile link-based query enable

Use srpm delay-profile link-based query enable to enable link-based SRPM delay measurement query on an interface and associate a delay profile with the interface.

Use undo srpm delay-profile link-based query enable to disable link-based SRPM delay measurement query on an interface.

Syntax

srpm delay-profile link-based profile-name query enable

undo srpm delay-profile link-based profile-name query enable

Default

Link-based SRPM delay measurement query is disabled on an interface.

Views

Layer 3 interface view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a link-based SRPM delay profile by its name, a case-sensitive string of 1 to 31 characters. The name can contain only letters, digits, and underscores (_).

Usage guidelines

This command enables an interface to send SRPM delay measurement query packets. Use this command on the local end.

Before you use this command, create the delay profile that will be specified in this command and activate the profile by using the activate profile command. This configuration ensures that the link-based SRPM delay measurement query feature can take effect.

An interface can be associated only with one delay profile. To change the delay profile associated with an interface, you must first use the undo srpm delay-profile link-based query enable command to disable this feature.

Examples

# On interface Ten-GigabitEthernet 3/0/1, enable link-based SRPM delay measurement query and associate delay profile test with the interface.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/0/1

[Sysname-Ten-GigabitEthernet3/0/1] srpm delay-profile link-based test query enable

Related commands

activate profile

delay-profile link-based

srpm delay-profile link-based response enable

Use srpm delay-profile link-based response enable to enable link-based SRPM delay measurement response on an interface and associate a delay profile with the interface.

Use undo srpm delay-profile link-based response enable to disable link-based SRPM delay measurement response on an interface.

Syntax

srpm delay-profile link-based profile-name response enable

undo srpm delay-profile link-based profile-name response enable

Default

Link-based SRPM delay measurement response is disabled on an interface.

Views

Layer 3 interface view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a link-based SRPM delay profile by its name, a case-sensitive string of 1 to 31 characters. The name can contain only letters, digits, and underscores (_).

Usage guidelines

This command enables an interface to reply to a peer with SRPM delay measurement response packets. Use this command on the remote end.

Before you use this command, create the delay profile that will be specified in this command and activate the profile by using the activate profile command. This configuration ensures that the link-based SRPM delay measurement response feature can take effect.

An interface can be associated only with one delay profile. To change the delay profile associated with an interface, you must first use the undo srpm delay-profile link-based response enable command to disable this feature.

Examples

# On interface Ten-GigabitEthernet 3/0/1, enable link-based SRPM delay measurement response and associate delay profile test with the interface.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/0/1

[Sysname-Ten-GigabitEthernet3/0/1] srpm delay-profile link-based test response enable

Related commands

activate profile

delay-profile link-based

srpm destination

Use srpm destination to specify a destination IP address for SRPM packets.

Use undo srpm destination to restore the default.

Syntax

srpm destination { ipv4 ipv4-address | ipv6 ipv6-address }

undo srpm destination { ipv4 | ipv6 }

Default

No destination IP address is specified for SRPM packets.

Views

Layer 3 interface view

Predefined user roles

network-admin

Parameters

ipv4 ipv4-address: Specifies a destination IPv4 address.

ipv6 ipv6-address: Specifies a destination IPv6 address.

Usage guidelines

Use this command on an interface of the local end to specify the IP address of an interface on the remote end as the destination IP address of SRPM packets.

Examples

# On Ten-GigabitEthernet 3/0/1, specify destination IPv4 address 1.1.1.1 for SRPM packets.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/0/1

[Sysname-Ten-GigabitEthernet3/0/1] srpm destination 1.1.1.1

udp destination-port

Use udp destination-port to specify a destination UDP port number for SRPM packets.

Use undo udp destination-port to restore the default.

Syntax

udp destination-port port-number

undo udp destination-port

Default

The destination UDP port number is 5245 for SRPM delay measurement packets.

Views

Link-based delay profile view

Predefined user roles

network-admin

Parameters

port-number: Specifies a UDP port number in the range of 1 to 65535.

Usage guidelines

Use this command to modify the destination port number of SRPM packets to avoid port number conflicts. To obtain usage information about UDP port numbers, use the display udp command.

The destination port number on the local end must be the same as the source port number on the remote end.

The destination port number on the remote end must be the same as the source port number on the local end.

Use the udp destination-port command only when the delay profile is deactivated.

Examples

# Set the destination UDP port number to 8000 for SRPM packets.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] udp destination-port 8000

Related commands

activate profile

display udp (Layer 3—IP Services Command Reference)

udp source-port

Use udp source-port to specify a source UDP port number for SRPM packets.

Use undo udp source-port to restore the default.

Syntax

udp source-port port-number

undo udp source-port

Default

The source UDP port number is 5245 for SRPM delay measurement packets.

Views

Link-based delay profile view

Predefined user roles

network-admin

Parameters

port-number: Specifies a UDP port number in the range of 1 to 65535.

Usage guidelines

Use this command to modify the source port number of SRPM packets to avoid port number conflicts. To obtain usage information about UDP port numbers, use the display udp command.

The source port number on the local end must be the same as the destination port number on the remote end.

The source port number on the remote end must be the same as the destination port number on the local end.

Use the udp source-port command only when the delay profile is deactivated.

Examples

# Set the source UDP port number to 9000 for SRPM packets.

<Sysname> system-view

[Sysname] srpm

[Sysname-srpm] delay-profile link-based test

[Sysname-srpm-delay-profile-link-based-test] udp source-port 9000

Related commands

activate profile