Contents

Configuring port isolation· 1

About port isolation·· 1

Assigning a port to an isolation group· 1

Display and maintenance commands for port isolation·· 1

Port isolation configuration examples· 2

Example: Configuring port isolation·· 2

Configuring port isolation

About port isolation

The port isolation feature isolates Layer 2 traffic for data privacy and security without using VLANs.

Ports in an isolation group cannot communicate with each other. However, they can communicate with ports outside the isolation group.

Assigning a port to an isolation group

About port assignment to an isolation group

The device supports multiple isolation groups, which can be configured manually. The number of ports assigned to an isolation group is not limited.

Restrictions and guidelines

·          You can assign a port to only one isolation group. If you execute the port-isolate enable group command multiple times, the most recent configuration takes effect.

·          The configuration in Layer 2 Ethernet interface view applies only to the interface.

·          The configuration in Layer 2 aggregate interface view applies to the Layer 2 aggregate interface and its aggregation member ports. If the device fails to apply the configuration to the aggregate interface, it does not assign any aggregation member port to the isolation group. If the failure occurs on an aggregation member port, the device skips the port and continues to assign other aggregation member ports to the isolation group.

Procedure

1.        Enter system view.

system-view

2.        Create an isolation group.

port-isolate group group-id

3.        Enter interface view.

¡  Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡  Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

4.        Assign the port to the isolation group.

port-isolate enable group group-id

By default, the port is not in any isolation group.

Display and maintenance commands for port isolation

Execute display commands in any view.

Port isolation configuration examples

Example: Configuring port isolation

Network configuration

As shown in Figure 1:

·          LAN users Host A, Host B, and Host C are connected to GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 on the device, respectively.

·          The device connects to the Internet through GigabitEthernet 1/0/4.

Configure the device to provide Internet access for the hosts, and isolate them from one another at Layer 2.

Figure 1 Network diagram

‌

Procedure

# Create isolation group 2.

<Device> system-view

[Device] port-isolate group 2

# Assign GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 to isolation group 2.

[Device] interface gigabitethernet 1/0/1

[Device-GigabitEthernet1/0/1] port-isolate enable group 2

[Device-GigabitEthernet1/0/1] quit

[Device] interface gigabitethernet 1/0/2

[Device-GigabitEthernet1/0/2] port-isolate enable group 2

[Device-GigabitEthernet1/0/2] quit

[Device] interface gigabitethernet 1/0/3

[Device-GigabitEthernet1/0/3] port-isolate enable group 2

[Device-GigabitEthernet1/0/3] quit

Verifying the configuration

# Display information about isolation group 2.

[Device] display port-isolate group 2

 Port isolation group information:

 Group ID: 2

 Group members:

   GigabitEthernet1/0/1     GigabitEthernet1/0/2     GigabitEthernet1/0/3

The output shows that GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3 are assigned to isolation group 2. As a result, Host A, Host B, and Host C are isolated from one another at layer 2.