Contents

Introduction· 1

Prerequisites· 1

Restrictions and guidelines· 1

Example: Configuring IP unnumbered· 1

Network configuration· 1

Applicable hardware and software versions· 2

Procedures· 2

Configuring Device A· 2

Configuring Device B· 3

Configuring Device C· 3

Verifying the configuration· 4

Configuration files· 5

 

Introduction

This document provides IP unnumbered configuration examples.

This feature enables an interface to borrow an IP address from another interface on the device when the borrowing interface does not have any IP addresses. The borrowing interface is called IP unnumbered interface.

Prerequisites

The configuration examples in this document were created and verified in a lab environment, and all the devices were started with the factory default configuration. When you are working on a live network, make sure you understand the potential impact of every command on your network.

This document assumes that you have basic knowledge of IP unnumbered.

Restrictions and guidelines

When you configure IP unnumbered, follow these restrictions and guidelines:

·     Loopback interfaces cannot borrow IP addresses of other interfaces.

·     An interface cannot borrow an IP address from an unnumbered interface.

·     If an interface has multiple manually configured IP addresses, only the manually configured primary IP address can be borrowed.

Example: Configuring IP unnumbered

Network configuration

As shown in Figure 1, Group A and Group B are two private IPv4 networks. Device A and Device C will establish a GRE tunnel to interconnect Group 1 and Group 2.

To save IP address space, configure tunnel interface Tunnel 1 to borrow an IP address from the loopback interface loopback 0.

Figure 1 Network diagram

 

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

 

Hardware	Software version
S6520X-HI switch series S6520X-EI switch series	Supported in Release 1110P01
S6520X-SI switch series S6520-SI switch series S5000-EI switch series MS4600 switch series	Supported in Release 1110P01

 

Procedures

Configuring Device A

1.     Assign IP addresses to the interfaces:

# Assign IP addresses to Ten-GigabitEthernet 1/0/1 and loopback 0.

<DeviceA> system-view

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-mode route

[DeviceA-Ten-GigabitEthernet1/0/1] ip address 12.12.12.1 24

[DeviceA-Ten-GigabitEthernet1/0/1] quit

[DeviceA] interface loopback 0

[DeviceA-LoopBack0] ip address 8.8.8.8 32

[DeviceA-LoopBack0] quit

# Assign IP addresses to other interfaces in the same way an IP address is assigned to Ten-GigabitEthernet 1/0/1. (Details not shown.)

2.     Configure OSPF:

# Enable OSPF process 1.

[DeviceA] ospf 1

# Create Area 0 and specify Ten-GigabitEthernet 1/0/1 whose IP address is on network 12.12.12.0/24 to run OSPF in Area 0.

[DeviceA-ospf-1] area 0

[DeviceA-ospf-1-area-0.0.0.0] network 12.12.12.0 0.0.0.255

[DeviceA-ospf-1-area-0.0.0.0] quit

[DeviceA-ospf-1] quit

3.     Configure a GRE tunnel:

# Create service loopback group 1 and specify the unicast tunnel service for the group.

[DeviceA] service-loopback group 1 type tunnel

# Assign Ten-GigabitEthernet 1/0/3 to the service loopback group.

[DeviceA] interface ten-gigabitethernet 1/0/3

[DeviceA-Ten-GigabitEthernet1/0/3] port service-loopback group 1

[DeviceA-Ten-GigabitEthernet1/0/3] quit

# Create a tunnel interface Tunnel 1, and specify the tunnel mode as GRE/IPv4.

[DeviceA] interface tunnel 1 mode gre

# Specify 12.12.12.1 as the source address of interface Tunnel 1.

[DeviceA-Tunnel1] source 12.12.12.1

# Specify 23.23.23.3 as the destination address of interface Tunnel 1.

[DeviceA-Tunnel1] destination 23.23.23.3

# Configure interface Tunnel 1 to borrow an IP address from loopback 0.

[DeviceA-Tunnel1] ip address unnumbered interface loopback 0

[DeviceA-Tunnel1] quit

# Configure a static route from Device A through the tunnel interface to Group B.

[DeviceA] ip route-static 10.2.1.0 255.255.255.0 tunnel 1

Configuring Device B

1.     Assign IP addresses to the interfaces:

# Assign an IP address to Ten-GigabitEthernet 1/0/1.

<DeviceB> system-view

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-mode route

[DeviceB-Ten-GigabitEthernet1/0/1] ip address 12.12.12.2 24

[DeviceB-Ten-GigabitEthernet1/0/1] quit

# Assign an IP address to Ten-GigabitEthernet 1/0/2 in the same way an IP address is assigned to Ten-GigabitEthernet 1/0/1. (Details not shown.)

2.     Configure OSPF:

# Enable OSPF process 1.

[DeviceB] ospf 1

# Create Area 0 and specify Ten-GigabitEthernet 1/0/1 whose IP address is on network 12.12.12.0/24 to run OSPF in Area 0.

[DeviceB-ospf-1] area 0

[DeviceB-ospf-1-area-0.0.0.0] network 12.12.12.0 0.0.0.255

# Create Area 0 and specify Ten-GigabitEthernet 1/0/2 whose IP address is on network 23.23.23.0/24 to run OSPF in Area 0.

[DeviceB-ospf-1-area-0.0.0.0] network 23.23.23.0 0.0.0.255

[DeviceB-ospf-1-area-0.0.0.0] quit

[DeviceB-ospf-1] quit

Configuring Device C

1.     Assign IP addresses to the interfaces:

# Assign IP addresses to Ten-GigabitEthernet 1/0/1 and loopback 0.

<DeviceC> system-view

[DeviceC] interface ten-gigabitethernet 1/0/1

[DeviceC-Ten-GigabitEthernet1/0/1] port link-mode route

[DeviceC-Ten-GigabitEthernet1/0/1] ip address 23.23.23.3 24

[DeviceC-Ten-GigabitEthernet1/0/1] quit

[DeviceC] interface loopback 0

[DeviceC-LoopBack0] ip address 9.9.9.9 32

[DeviceC-LoopBack0] quit

# Assign IP addresses to other interfaces in the same way an IP address is assigned to Ten-GigabitEthernet 1/0/1. (Details not shown.)

2.     Configure OSPF:

# Enable OSPF process 1.

[DeviceC] ospf 1

# Create Area 0 and specify Ten-GigabitEthernet 1/0/1 whose IP address is on network 23.23.23.0/24 to run OSPF in Area 0.

[DeviceC-ospf-1] area 0

[DeviceC-ospf-1-area-0.0.0.0] network 23.23.23.0 0.0.0.255

[DeviceC-ospf-1-area-0.0.0.0] quit

[DeviceC-ospf-1] quit

3.     Configure a GRE tunnel:

# Create service loopback group 1 and specify the unicast tunnel service for the group.

[DeviceC] service-loopback group 1 type tunnel

# Assign Ten-GigabitEthernet 1/0/3 to the service loopback group.

[DeviceC] interface ten-gigabitethernet 1/0/3

[DeviceC-Ten-GigabitEthernet1/0/3] port service-loopback group 1

[DeviceC-Ten-GigabitEthernet1/0/3] quit

# Create a tunnel interface Tunnel 1, and specify the tunnel mode as GRE/IPv4.

[DeviceC] interface tunnel 1 mode gre

# Specify 23.23.23.3 as the source address of interface Tunnel 1.

[DeviceC-Tunnel1] source 23.23.23.3

# Specify 12.12.12.1 as the destination address of interface Tunnel 1.

[DeviceC-Tunnel1] destination 12.12.12.1

# Configure interface Tunnel 1 to borrow an IP address from loopback 0.

[DeviceC-Tunnel1] ip address unnumbered interface loopback 0

[DeviceC-Tunnel1] quit

# Configure a static route from Device C through the tunnel interface to Group A.

[DeviceC] ip route-static 10.1.1.0 255.255.255.0 tunnel 1

Verifying the configuration

This example uses Device A to verify the configuration.

# Verify that the interface Tunnel 1 has borrowed the IP address 8.8.8.8/32 from loopback 0.

[DeviceA] display interface tunnel 1

Tunnel1

Current state: UP

Line protocol state: UP

Description: Tunnel1 Interface

Bandwidth: 64kbps

Maximum transmission unit: 1476

Internet Address: 8.8.8.8/32 (Unnumbered)

Tunnel source 12.12.12.1, destination 23.23.23.3

Tunnel keepalive disabled

Tunnel TTL 255

Tunnel protocol/transport GRE/IP

    GRE key disabled

    Checksumming of GRE packets disabled

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 11 packets, 924 bytes, 0 drops

Output: 10 packets, 840 bytes, 0 drops

# Verify that Ten-GigabitEthernet 1/0/2 on Device A can ping the IP address of Ten-GigabitEthernet 1/0/2 on Device C.

# Verify that VLAN-interface 10 on Device A can ping the IP address of VLAN-interface 10 on Device C.

[DeviceA] ping -a 10.1.1.1 10.2.1.1

Ping 10.2.1.1 (10.2.1.1) from 10.1.1.1: 56 data bytes, press CTRL_C to break

56 bytes from 10.2.1.1: icmp_seq=0 ttl=255 time=32.641 ms

56 bytes from 10.2.1.1: icmp_seq=1 ttl=255 time=4.881 ms

56 bytes from 10.2.1.1: icmp_seq=2 ttl=255 time=4.816 ms

56 bytes from 10.2.1.1: icmp_seq=3 ttl=255 time=26.393 ms

56 bytes from 10.2.1.1: icmp_seq=4 ttl=255 time=43.003 ms

 

--- Ping statistics for 10.2.1.1 ---

5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss

round-trip min/avg/max/std-dev = 4.816/22.347/43.003/15.241 ms

Configuration files

·     Device A:

#

 service-loopback group 1 type tunnel

#

ospf 1

 area 0.0.0.0

  network 12.12.12.0 0.0.0.255

#

vlan 10

#

vlan 12

#

interface LoopBack0

 ip address 8.8.8.8 255.255.255.255

#

interface Vlan-interface10

 ip address 10.1.1.1 255.255.255.0

#

interface Vlan-interface12

 ip address 12.12.12.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode route

 ip address 12.12.12.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/2

 port link-mode route

 ip address 10.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port service-loopback group 1

#

interface Tunnel1 mode gre

 ip address unnumbered interface LoopBack0

 source 12.12.12.1

 destination 23.23.23.3

#

 ip route-static 10.2.1.0 24 Tunnel1

#

·     Device B:

#

ospf 1

 area 0.0.0.0

  network 12.12.12.0 0.0.0.255

  network 23.23.23.0 0.0.0.255

#

vlan 12

#

vlan 23

#

interface Vlan-interface12

 ip address 12.12.12.2 255.255.255.0

#

interface Vlan-interface23

 ip address 23.23.23.3 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode route

 ip address 12.12.12.2 255.255.255.0

#

interface Ten-GigabitEthernet1/0/2

 port link-mode route

 ip address 23.23.23.2 255.255.255.0

#

·     Device C:

#

 service-loopback group 1 type tunnel

#

ospf 1

 area 0.0.0.0

  network 23.23.23.0 0.0.0.255

#

vlan 10

#

vlan 23

#

interface LoopBack0

 ip address 9.9.9.9 255.255.255.255

#

interface Vlan-interface10

 ip address 10.2.1.1 255.255.255.0

#

interface Vlan-interface23

 ip address 23.23.23.3 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode route

 ip address 23.23.23.3 255.255.255.0

#

interface Ten-GigabitEthernet1/0/2

 port link-mode route

 ip address 10.2.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port service-loopback group 1

#

interface Tunnel1 mode gre

 ip address unnumbered interface LoopBack0

 source 23.23.23.3

 destination 12.12.12.1

#

 ip route-static 10.1.1.0 24 Tunnel1

#