AP License共享典型配置举例

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

目  录

1 简介

2 配置前提

3 配置举例

3.1 组网需求

3.2 配置注意事项

3.3 配置步骤

3.3.1 配置AC1

3.3.2 配置AC2

3.3.3 配置Switch

3.4 验证配置

3.5 配置文件

4 相关资料

 

1  简介

本文档介绍了AP License共享典型配置举例。

2  配置前提

本文档不严格与具体软、硬件版本对应，如果使用过程中与产品实际情况有差异，请以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置，为了保证配置效果，请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解AP License共享特性。

3  配置举例

3.1  组网需求

如图1所示，AP通过交换机与AC1和AC2相连，AP为Client提供无线服务，配置SSID为service，在AC1和AC2上开启AP License共享功能，两台AC互为备份，当一台AC出现故障时，License也可以在备AC上继续使用。

图1 AP License共享组网图

 

3.2  配置注意事项

当一台AC出现故障时，License可以在备AC上继续使用的有效期为30天。

3.3  配置步骤

3.3.1  配置AC1

(1)     配置AC1的接口

# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IP地址。AP将通过该IP地址与AC1建立CAPWAP隧道。

<AC1> system-view

[AC1] vlan 100

[AC1-vlan100] quit

[AC1] interface vlan-interface 100

[AC1-Vlan-interface100] ip address 112.12.1.25 16

[AC1-Vlan-interface100] quit

# 创建VLAN 200及其对应的VLAN接口，并为该接口配置IP地址。Client使用VLAN 200接入无线网络。

[AC1] vlan 200

[AC1-vlan200] quit

[AC1] interface vlan-interface 200

[AC1-Vlan-interface200] ip address 112.13.1.25 16

[AC1-Vlan-interface200] quit

# 配置AC1和Switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过。

[AC1] interface gigabitethernet1/0/1

[AC1-GigabitEthernet1/0/1] port link-type trunk

[AC1-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC1-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC1-GigabitEthernet1/0/1] quit

(2)     配置AP license共享功能，配置角色为主AC

[AC1] wlan ap-license-group

[AC1-wlan-ap-license-group] local ip 112.12.1.25

[AC1-wlan-ap-license-group] member ip 112.12.1.26

[AC1-wlan-ap-license-group] ap-license-synchronization enable

[AC1-wlan-ap-license-group] quit

(3)     配置无线服务

# 创建无线服务模板service，并配置SSID为service，配置Client从无线服务模板service上线后会被加入VLAN 200。

[AC1] wlan service-template service

[AC1-wlan-st-service] ssid service

[AC1-wlan-st-service] vlan 200

# 配置身份认证与密钥管理模式为PSK模式，配置PSK密钥为明文字符串12345678。

[AC1-wlan-st-service] akm mode psk

[AC1-wlan-st-service] preshared-key pass-phrase simple 12345678

# 配置加密套件为CCMP，安全信息元素为RSN。

[AC1-wlan-st-service] cipher-suite ccmp

[AC1-wlan-st-service] security-ie rsn

# 配置无线客户端的数据报文转发位置在AC上。（如果客户端数据报文的缺省转发位置与本配置相同，请跳过此步骤）

[AC1-wlan-st-service] client forwarding-location ac

# 使能无线服务模板。

[AC1-wlan-st-service] service-template enable

[AC1-wlan-st-service] quit

(4)     配置AP

 

# 创建AP，名称为ap1，选择AP型号并配置序列号。

[AC1] wlan ap ap1 model WA6320

[AC1-wlan-ap-ap1] serial-id 219801A28N819CE0002T

[AC1-wlan-ap-ap1] quit

# 创建AP组group1，并配置AP名称入组规则。

[AC1] wlan ap-group group1

[AC-wlan-ap-group-group1] ap ap1

# 将无线服务模板service绑定到AP组group1下的Radio 1接口，并开启射频功能。

[AC1-wlan-ap-group-group1] ap-model WA6320

[AC1-wlan-ap-group-group1-ap-model-WA6320] radio 1

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] service-template service

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] radio enable

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] quit

[AC1-wlan-ap-group-group1-ap-model-WA6320] quit

[AC1-wlan-ap-group-group1] quit

3.3.2  配置AC2

(1)     配置AC2的接口

# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IP地址。AP将通过该IP地址与AC2建立CAPWAP隧道。

<AC2> system-view

[AC2] vlan 100

[AC2-vlan100] quit

[AC2] interface vlan-interface 100

[AC2-Vlan-interface100] ip address 112.12.1.26 16

[AC2-Vlan-interface100] quit

# 创建VLAN 200及其对应的VLAN接口，并为该接口配置IP地址。Client使用VLAN 200接入无线网络。

[AC2] vlan 200

[AC2-vlan200] quit

[AC2] interface vlan-interface 200

[AC2-Vlan-interface200] ip address 112.13.1.26 16

[AC2-Vlan-interface200] quit

# 配置AC2和Switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过。

[AC2] interface gigabitethernet1/0/1

[AC2-GigabitEthernet1/0/1] port link-type trunk

[AC2-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC2-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC2-GigabitEthernet1/0/1] quit

(2)     配置AP license共享功能，配置角色为主AC

[AC2] wlan ap-license-group

[AC2-wlan-ap-license-group] local ip 112.12.1.26

[AC2-wlan-ap-license-group] member ip 112.12.1.25

[AC2-wlan-ap-license-group] ap-license-synchronization enable

[AC2-wlan-ap-license-group] quit

(3)     配置无线服务

# 创建无线服务模板service，并配置SSID为service，配置Client从无线服务模板service上线后会被加入VLAN 200。

[AC2] wlan service-template service

[AC2-wlan-st-service] ssid service

[AC2-wlan-st-service] vlan 200

# 配置身份认证与密钥管理模式为PSK模式，配置PSK密钥为明文字符串12345678。

[AC2-wlan-st-service] akm mode psk

[AC2-wlan-st-service] preshared-key pass-phrase simple 12345678

# 配置加密套件为CCMP，安全信息元素为RSN。

[AC2-wlan-st-service] cipher-suite ccmp

[AC2-wlan-st-service] security-ie rsn

# 配置无线客户端的数据报文转发位置在AC上。（如果客户端数据报文的缺省转发位置与本配置相同，请跳过此步骤）

[AC2-wlan-st-service] client forwarding-location ac

# 使能无线服务模板。

[AC2-wlan-st-service] service-template enable

[AC2-wlan-st-service] quit

(4)     配置AP

 

# 创建AP，名称为ap1，选择AP型号并配置序列号。

[AC2] wlan ap ap1 model WA6320

[AC2-wlan-ap-ap1] serial-id 219801A28N819CE0002T

[AC2-wlan-ap-ap1] quit

# 创建AP组group1，并配置AP名称入组规则。

[AC2] wlan ap-group group1

[AC2-wlan-ap-group-group1] ap ap1

# 将无线服务模板service绑定到AP组group1下的Radio 1接口，并开启射频功能。

[AC2-wlan-ap-group-group1] ap-model WA6320

[AC2-wlan-ap-group-group1-ap-model-WA6320] radio 1

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] service-template service

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] radio enable

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] quit

[AC2-wlan-ap-group-group1-ap-model-WA6320] quit

[AC2-wlan-ap-group-group1] quit

3.3.3  配置Switch

# 创建VLAN 100和VLAN 200，其中VLAN 100用于转发AC和AP间CAPWAP隧道内的流量，VLAN 200用于转发Client无线报文。

<Switch> system-view

[Switch] vlan 100

[Switch-vlan100] quit

[Switch] vlan 200

[Switch-vlan200] quit

# 配置Switch与AC1相连的GigabitEthernet1/0/1接口的属性为Trunk，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过。

[Switch] interface gigabitethernet1/0/1

[Switch-GigabitEthernet1/0/1] port link-type trunk

[Switch-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[Switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/1] quit

# 配置Switch与AC2相连的GigabitEthernet1/0/2接口的属性为Trunk，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过。

[Switch] interface gigabitethernet1/0/2

[Switch-GigabitEthernet1/0/2] port link-type trunk

[Switch-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[Switch-GigabitEthernet1/0/2] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/2] quit

# 配置Switch与AP相连的接口属性为Access，并允许VLAN 100通过，本例仅示例1个接口的配置。

[Switch] interface gigabitethernet1/0/3

[Switch-GigabitEthernet1/0/3] port link-type access

[Switch-GigabitEthernet1/0/3] port access vlan 100

# 开启PoE接口远程供电功能。

[Switch-GigabitEthernet1/0/3] poe enable

[Switch-GigabitEthernet1/0/3] quit

# 配置VLAN 100接口的IP地址。

[Switch] interface vlan-interface 100

[Switch-Vlan-interface100] ip address 112.12.1.27 16

[Switch-Vlan-interface100] quit

# 配置VLAN 200接口的IP地址。

[Switch] interface vlan-interface 200

[Switch-Vlan-interface200] ip address 112.13.1.27 16

[Switch-Vlan-interface200] quit

 # 开启DHCP功能。

[Switch] dhcp enable

# 配置DHCP地址池100，用于为AP分配IP地址。

[Switch] dhcp server ip-pool 100

[Switch-dhcp-pool-100] network 112.12.0.0 mask 255.255.0.0

[Switch-dhcp-pool-100] gateway-list 112.12.1.27

[Switch-dhcp-pool-100] quit

# 配置DHCP地址池200，用于为Client分配IP地址。为Client分配的DNS服务器地址为网关地址（实际使用过程中请根据实际网络规划配置无线客户端的DNS服务器地址）。

[Switch] dhcp server ip-pool 200

[Switch-dhcp-pool-200] network 112.13.0.0 mask 255.255.255.0

[Switch-dhcp-pool-200] gateway-list 112.13.1.27

[Switch-dhcp-pool-200] dns-list 112.13.1.27

[Switch-dhcp-pool-200] quit

3.4  验证配置

(1)     在AC1可以查看AP license共享组已经建立。

<AC1> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.25

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.26      16        0       Master        UP      10hr 22min 04sec

(2)     在AC2可以查看AP license共享组已经建立。

<AC2> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.26

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.25      16        2       Master        UP      10hr 22min 04sec

(3)     当AC2出现故障后，AC1可以继续使用组内的License，可以查看AP license共享组总license数仍然为32。

<AC1> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.25

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.26      16        0       Master        DOWM    00hr 00min 00sec

3.5  配置文件

·     AC1：

#

vlan 100

#

vlan 200

#

wlan service-template service

 ssid service

 vlan 200

 client forwarding-location ac

 akm mode psk

 preshared-key pass-phrase cipher $c$3$QoCUXs4DmEXLHV9i25HKOnf4wdvj4i8EzJb+

 cipher-suite ccmp

 security-ie rsn

 service-template enable

#

interface Vlan-interface100

 ip address 112.12.1.25 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.25 255.255.0.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 200

#

wlan ap-group group1

 ap ap1

 ap-model WA6320

  radio 1

   radio enable

   service-template service

#

wlan ap ap1 model WA6320

 serial-id 219801A28N819CE0002T

#

wlan ap-license-group

 local ip 112.12.1.25

 member ip 112.12.1.26

 ap-license-synchronization enable

#

·     AC2：

#

vlan 100

#

vlan 200

#

wlan service-template service

 ssid service

 vlan 200

 client forwarding-location ac

 akm mode psk                                                                  

 preshared-key pass-phrase cipher $c$3$QoCUXs4DmEXLHV9i25HKOnf4wdvj4i8EzJb+    

 cipher-suite ccmp                                                              

 security-ie rsn

 service-template enable

#

interface Vlan-interface100

 ip address 112.12.1.26 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.26 255.255.0.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 200

#

wlan ap-group group1

 ap ap1

 ap-model WA6320

  radio 1

   radio enable

   service-template service

#

wlan ap ap1 model WA6320

 serial-id 219801A28N819CE0002T

#

wlan ap-license-group

 local ip 112.12.1.26

 member ip 112.12.1.25

 ap-license-synchronization enable

#

·     Switch：

#

 dhcp enable

#

vlan 100

#

vlan 200

#

dhcp server ip-pool vlan100

 gateway-list 112.12.1.27

 network 112.12.0.0 mask 255.255.0.0

#

dhcp server ip-pool vlan200

gateway-list 112.13.1.27

 network 112.13.0.0 mask 255.255.255.0

 dns-list 112.13.1.27

#

interface Vlan-interface100

 ip address 112.12.1.27 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.27 255.255.255.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

undo port trunk permit vlan 1 

 port trunk permit vlan 100 200

#

interface GigabitEthernet1/0/2

 port link-type trunk

undo port trunk permit vlan 1 

 port trunk permit vlan 100 200

#

interface GigabitEthernet1/0/3

 port access vlan 100

 poe enable

#

4  相关资料

·     《H3C无线控制器产品 配置指导》中的“License管理配置指导”。

·     《H3C无线控制器产品 命令参考》中的“License管理命令参考”。