Field	Description
Global 802.1X parameters	Global 802.1X configuration.
802.1X authentication	Whether 802.1X is enabled globally.
CHAP authentication	Performs EAP termination and uses CHAP to communicate with the RADIUS server.
EAP authentication	Relays EAP packets and supports any of the EAP authentication methods to communicate with the RADIUS server.
PAP authentication	Performs EAP termination and uses PAP to communicate with the RADIUS server.
Max-tx period	Username request timeout timer in seconds.
Handshake period	Handshake timer in seconds.
Offline detect period	Offline detect timer in seconds.
Quiet timer	Status of the quiet timer, enabled or disabled.
Quiet period	Quiet timer in seconds.
Supp timeout	Client timeout timer in seconds.
Server timeout	Server timeout timer in seconds.
Reauth period	Periodic reauthentication timer in seconds.
Max auth requests	Maximum number of attempts for sending an authentication request to a client.
User aging period for Auth-Fail VLAN	Aging timer in seconds for users in Auth-Fail VLANs.
User aging period for Auth-Fail VSI	Aging timer in seconds for users in Auth-Fail VSIs.
User aging period for critical VLAN	Aging timer in seconds for users in critical VLANs.
User aging period for critical VSI	Aging timer in seconds for users in critical VSIs.
User aging period for guest VLAN	Aging timer in seconds for users in guest VLANs.
User aging period for guest VSI	Aging timer in seconds for users in the guest VSIs.
EAD assistant function	Whether EAD assistant is enabled.
URL	Redirect URL for unauthenticated users using a Web browser to access the network.
Free IP	Network segment accessible to unauthenticated users.
EAD timeout	EAD rule timer in minutes.
Domain delimiter	Domain delimiters supported by the device.
Max EAP-TLS fragment (to-server)	Maximum size of EAP-TLS fragments sent in authentication packets to the server. If no maximum size is set, this field displays N/A.
Online 802.1X wired users	Number of wired online 802.1X users, including users that have passed 802.1X authentication and users that are performing 802.1X authentication.
Twenty-FiveGigE1/0/1 is link-up	Status of the port. In this example, Twenty-FiveGigE 1/0/1 is up.
802.1X authentication	Whether 802.1X is enabled on the port.
Handshake	Whether the online user handshake feature is enabled on the port.
Handshake reply	Whether the online user handshake reply feature is enabled on the port.
Handshake security	Whether the online user handshake security feature is enabled on the port.
Offline detection	Status of 802.1X offline detection: · Enabled—This feature is enabled and effective. · Disabled—This feature is disabled. · Enabled(NOT effective)—This feature is enabled but it does not take effect. This state is displayed when the port access control mode is port-based.
Unicast trigger	Whether the 802.1X unicast trigger is enabled on the port.
Periodic reauth	Whether 802.1X periodic reauthentication is enabled on the port.
Port role	Role of the port. The port functions only as an Authenticator.
Authorization mode	Authorization state of the port, which can be Force-Authorized, Auto, or Force-Unauthorized.
Port access control	Access control method of the port: · MAC-based—MAC-based access control. · Port-based—Port-based access control.
Multicast trigger	Whether the 802.1X multicast trigger feature is enabled.
Mandatory auth domain	Mandatory authentication domain on the port.
Guest VLAN	802.1X guest VLAN configured on the port. If no 802.1X guest VLAN is configured on the port, this field displays Not configured.
Auth-Fail VLAN	802.1X Auth-Fail VLAN configured on the port. If no 802.1X Auth-Fail VLAN is configured on the port, this field displays Not configured.
Critical VLAN	802.1X critical VLAN configured on the port. If no 802.1X critical VLAN is configured on the port, this field displays Not configured.
Critical voice VLAN	Whether the 802.1X critical voice VLAN feature is enabled on the port.
Add Guest VLAN delay	Status and mode of the 802.1X guest VLAN assignment delay feature on a port: · EAPOL—EAPOL-triggered 802.1X guest VLAN assignment delay is enabled. · NewMac—New MAC-triggered 802.1X guest VLAN assignment delay is enabled. · ALL—Both EAPOL-triggered and new MAC-triggered 802.1X guest VLAN assignment delays are enabled. · Disabled—802.1X guest VLAN assignment delay is disabled.
Re-auth server-unreachable	Whether to log off online 802.1X users or keep them online when no server is reachable for 802.1X reauthentication.
Max online users	Maximum number of concurrent 802.1X users on the port.
User IP freezing	Whether user IP freezing is enabled on the port.
Reauth period	Periodic reauthentication timer in seconds on the port.
Send Packets Without Tag	Whether to remove the VLAN tags of all 802.1X protocol packets sent out of the port to 802.1X clients.
Max Attempts Fail Number	Maximum number of 802.1X authentication attempts for MAC authenticated users.
Guest VSI	802.1X guest VSI configured on the port. If no 802.1X guest VSI is configured on the port, this field displays Not configured.
Auth-Fail VSI	802.1X Auth-Fail VSI configured on the port. If no 802.1X Auth-Fail VSI is configured on the port, this field displays Not configured.
Critical VSI	802.1X critical VSI configured on the port. If no 802.1X critical VSI is configured on the port, this field displays Not configured.
Add Guest VSI delay	Status and mode of the 802.1X guest VSI assignment delay feature on a port: · EAPOL only—EAPOL-triggered 802.1X guest VSI assignment delay is enabled. · NewMAC only—New MAC-triggered 802.1X guest VSI assignment delay is enabled. · EAPOL or NewMAC—Both EAPOL-triggered and new MAC-triggered 802.1X guest VSI assignment delays are enabled. · Disabled—802.1X guest VSI assignment delay is disabled.
User aging	Status of 802.1X unauthenticated user aging on a port: · Enabled. · Disabled.
Server-recovery online-user-sync	Status of 802.1X online user synchronization: · Enabled. · Disabled.
Auth-Fail EAPOL	This field displays whether the device sends EAP-Success packets to 802.1X clients on their assignment to the 802.1X Auth-Fail VLAN or VSI on the port.
Critical EAPOL	This field displays whether the device sends EAP-Success packets to 802.1X clients on their assignment to the 802.1X critical VLAN or VSI on the port.
EAPOL packets	Number of sent (Tx) and received (Rx) EAPOL packets.
Sent EAP Request/Identity packets	Number of sent EAP-Request/Identity packets.
EAP Request/Challenge packets	Number of sent EAP-Request/MD5-Challenge packets.
EAP Success packets	Number of sent EAP-Success packets.
EAP Failure packets	Number of sent EAP-Failure packets.
Received EAPOL Start packets	Number of received EAPOL-Start packets.
EAPOL LogOff packets	Number of received EAPOL-LogOff packets.
EAP Response/Identity packets	Number of received EAP-Response/Identity packets.
EAP Response/Challenge packets	Number of received EAP-Response/MD5-Challenge packets.
Error packets	Number of received error packets.
Online 802.1X users	Number of online 802.1X users on the port, including users that have passed 802.1X authentication and users that are performing 802.1X authentication.
MAC address	MAC addresses of the online 802.1X users.
Auth state	Authentication status of the online 802.1X users.

display dot1x connection

Use display dot1x connection to display information about online 802.1X users.

Syntax

display dot1x connection [ open ] [ interface interface-type interface-number | slot slot-number | user-mac mac-address | user-name name-string ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

open: Displays information only about 802.1X users that use nonexistent usernames or incorrect passwords for network access in open authentication mode. If you do not specify this keyword, the command displays information about all online 802.1X users.

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify a port, this command displays online 802.1X user information for all ports.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays online 802.1X user information for all member devices.

user-mac mac-address: Specifies an 802.1X user by MAC address. The mac-address argument represents the MAC address of the user, in the form of H-H-H. If you do not specify an 802.1X user, this command displays all online 802.1X user information.

user-name name-string: Specifies an 802.1X user by its name. The name-string argument represents the username, a case-sensitive string of 1 to 253 characters. If you do not specify an 802.1X user, this command displays all online 802.1X user information.

Examples

# Display information about all online 802.1X users.

<Sysname> display dot1x connection

Total connections: 1

Slot ID: 1

User MAC address: 0015-e9a6-7cfe

Access interface: Twenty-FiveGigE1/0/1

Username: ias

User access state: Successful

Authentication domain: h3c

IPv4 address: 192.168.1.1

IPv6 address: 2000:0:0:0:1:2345:6789:abcd

Authentication method: CHAP

Initial VLAN: 1

Authorization untagged VLAN: 6

Authorization tagged VLAN list: 1 to 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 29 31 33

35 37 40 to 100

Authorization VSI: N/A

Authorization ACL number/name: 3001

Authorization user profile: N/A

Authorization CAR: N/A

Authorization URL: N/A

Termination action: Default

Session timeout period: 2 s

Online from: 2013/03/02 13:14:15

Online duration: 0h 2m 15s

Table 2 Command output

Field	Description
Total connections	Number of online 802.1X users.
User MAC address	MAC address of the user.
Access interface	Interface through which the user access the device.
User access state	Access state of the user. · Successful—The user passes 802.1X authentication and comes online. · Open—The user uses a nonexistent username or an incorrect password to come online in open authentication mode.
Authentication domain	ISP domain used for 802.1X authentication.
IPv4 address	IPv4 address of the user. If the device does not get the IPv4 address of the user, this field is not available.
IPv6 address	IPv6 address of the user. If the device does not get the IPv6 address of the user, this field is not available.
Authentication method	EAP message handling method: · CHAP—Performs EAP termination and uses CHAP to communicate with the RADIUS server. · EAP—Relays EAP packets and supports any of the EAP authentication methods to communicate with the RADIUS server. · PAP—Performs EAP termination and uses PAP to communicate with the RADIUS server.
Initial VLAN	VLAN to which the user belongs before 802.1X authentication.
Authorization untagged VLAN	Untagged VLAN authorized to the user. The VLAN assigned by the server to a user as an authorization VLAN might have been configured on the user access port but with a different tagging mode. For example, the server assigns an authorization VLAN with a tagged attribute, but the same VLAN configured on the port has an untagged attribute. In this situation, if the link type of the port is hybrid, the VLAN settings configured on the port take effect on the user. For more information, see 802.1X in Security Configuration Guide.
Authorization tagged VLAN list	Tagged VLANs authorized to the user. The VLAN assigned by the server to a user as an authorization VLAN might have been configured on the user access port but with a different tagging mode. For example, the server assigns an authorization VLAN with a tagged attribute, but the same VLAN configured on the port has an untagged attribute. In this situation, if the link type of the port is hybrid, the VLAN settings configured on the port take effect on the user. For more information, see 802.1X in Security Configuration Guide.
Authorization VSI	VSIs authorized to the user.
Authorization ACL number/name	Number or name of the ACL authorized to the user. If no ACL is authorized to the user, this field displays N/A. If the ACL authorization fails, this field displays (Not effective) next to the ACL number or name.
Authorization user profile	User profile authorized to the user.
Authorization CAR	This field is not supported in the current software version. Authorization CAR attributes assigned by the server. If no authorization CAR attributes are assigned, this field displays N/A.
Authorization URL	Redirect URL authorized to the user.
Termination action	Action attribute assigned by the server to terminate the user session: · Default—Logs off the online authenticated 802.1X user when the server-assigned session timeout timer expires. This attribute does not take effect when 802.1X periodic reauthentication is enabled and the periodic reauthentication timer is shorter than the server-assigned session timeout timer. · Radius-request—Reauthenticates the online user when the server-assigned session timeout timer expires, regardless of whether the 802.1X periodic reauthentication feature is enabled or not. If the device performs local authentication, this field displays Default.
Session timeout period	Session timeout timer assigned by the server.
Online from	Time from which the 802.1X user came online.
Online duration	Online duration of the 802.1X user.

display dot1x mac-address

Use display dot1x mac-address to display the MAC addresses of 802.1X users in a type of 802.1X VLAN or VSI.

Syntax

display dot1x mac-address { auth-fail-vlan | auth-fail-vsi | critical-vlan | critical-vsi | guest-vlan | guest-vsi } [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

auth-fail-vlan: Specifies 802.1X Auth-Fail VLANs.

auth-fail-vsi: Specifies 802.1X Auth-Fail VSIs.

critical-vlan: Specifies 802.1X critical VLANs.

critical-vsi: Specifies 802.1X critical VSIs.

guest-vlan: Specifies 802.1X guest VLANs.

guest-vsi: Specifies 802.1X guest VSIs.

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify a port, this command displays the MAC addresses of 802.1X users in the specified type of 802.1X VLAN or VSI on all ports.

Usage guidelines

The displayed MAC addresses and MAC address count might not include all MAC addresses if a large number of 802.1X users are performing authentication frequently.

Examples

# Display the MAC addresses of 802.1X users in the 802.1X Auth-Fail VLANs on all ports.

<Sysname> display dot1x mac-address auth-fail-vlan

Total MAC addresses: 10

Interface: Twenty-FiveGigE1/0/1 Auth-Fail VLAN: 3 Aging time: N/A

MAC addresses: 8

0800-2700-9427 0800-2700-2341 0800-2700-2324 0800-2700-2351

0800-2700-5627 0800-2700-2251 0800-2700-8624 0800-2700-3f51

Interface: Twenty-FiveGigE1/0/2 Auth-Fail VLAN: 5 Aging time: 30 sec

MAC addresses: 2

0801-2700-9427 0801-2700-2341

# Display the MAC addresses of 802.1X users in the 802.1X Auth-Fail VSIs on all ports.

<Sysname> display dot1x mac-address auth-fail-vsi

Total MAC addresses: 10

Interface: Twenty-FiveGigE1/0/3 Auth-Fail VSI: text-vsi Aging time: N/A

MAC addresses: 8

0800-2700-9427 0800-2700-2341 0800-2700-2324 0800-2700-2351

0800-2700-5627 0800-2700-2251 0800-2700-8624 0800-2700-3f51

Interface: Twenty-FiveGigE1/0/4 Auth-Fail VSI: text1-vsi Aging time: 30 sec

MAC addresses: 2

0801-2700-9427 0801-2700-2341

Table 3 Command output

Field	Description
Total MAC addresses	Total number of MAC addresses in the specified type of VLAN or VSI on the specified port or all ports.
Interface	Access port of 802.1X users.
Type VLAN/VSI	VLAN or VSI that contains the 802.1X users. Available VLAN and VSI types: · Auth-Fail VLAN. · Auth-Fail VSI. · Critical VLAN. · Critical VSI. · Guest VLAN. · Guest VSI.
Aging time	MAC address aging time in seconds. This field displays N/A if the MAC addresses do not age out.
MAC addresses	Number of matching MAC addresses on a port.
xxxx-xxxx-xxxx	MAC address.

‌

Related commands

dot1x auth-fail vlan

dot1x auth-fail vsi

dot1x critical vlan

dot1x critical vsi

dot1x guest-vlan

dot1x guest-vsi

dot1x

Use dot1x to enable 802.1X globally or on a port.

Use undo dot1x to disable 802.1X globally or on a port.

Syntax

dot1x

undo dot1x

Default

802.1X is neither enabled globally nor enabled for any port.

Views

System view

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

For the 802.1X feature to take effect on a port, you must enable the feature both globally and on the port.

Examples

# Enable 802.1X globally.

<Sysname> system-view

[Sysname] dot1x

# Enable 802.1X on Twenty-FiveGigE 1/0/1.

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x

[Sysname-Twenty-FiveGigE1/0/1] quit

Related commands

display dot1x

dot1x access-user log enable

Use dot1x access-user log enable to enable 802.1X user logging.

Use undo dot1x access-user log enable to disable 802.1X user logging.

Syntax

dot1x access-user log enable [ abnormal-logoff | failed-login | normal-logoff | successful-login ] *

undo dot1x access-user log enable [ abnormal-logoff | failed-login | normal-logoff | successful-login ] *

Default

802.1X user logging is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

abnormal-logoff: Logs exceptional logoffs of 802.1X users, such as logoffs caused by real-time accounting failures or reauthentication failures.

failed-login: Logs 802.1X user login failures.

normal-logoff: Logs logoffs requested by 802.1X users.

successful-login: Logs successful 802.1X user logins.

Usage guidelines

To prevent excessive 802.1X user log entries, use this feature only if you need to analyze abnormal 802.1X user logins or logouts.

If you do not specify any parameters, this command enables all types of 802.1X user logs.

Examples

# Enable logging 802.1X user login failures.

<Sysname> system-view

[Sysname] dot1x access-user log enable failed-login

Related commands

info-center source dot1x logfile deny (Network Management and Monitoring Command Reference)

dot1x after-mac-auth max-attempt

Use dot1x after-mac-auth max-attempt to set the maximum number of 802.1X authentication attempts for MAC authenticated users on a port.

Use undo dot1x after-mac-auth max-attempt to restore the default.

Syntax

dot1x after-mac-auth max-attempt max-attempts

undo dot1x after-mac-auth max-attempt

Default

The number of 802.1X authentication attempts for MAC authenticated users is not limited on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

max-attempts: Specifies a number in the range of 1 to 50.

Usage guidelines

The device denies 802.1X authentication requests of a MAC authenticated user after the maximum number of 802.1X authentication attempts has been made.

The device will recount the number of 802.1X authentication attempts made by a MAC authenticated user if a user logoff or device reboot event occurs.

Examples

# Configure Twenty-FiveGigE 1/0/1 to allow a maximum of 10 802.1X authentication attempts made by a MAC authenticated user.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x after-mac-auth max-attempt 10

Related commands

display dot1x

dot1x authentication-method

Use dot1x authentication-method to specify an EAP message handling method.

Use undo dot1x authentication-method to restore the default.

Syntax

dot1x authentication-method { chap | eap | pap }

undo dot1x authentication-method

Default

The access device performs EAP termination and uses CHAP to communicate with the RADIUS server.

Views

System view

Predefined user roles

network-admin

Parameters

chap: Configures the access device to perform Extensible Authentication Protocol (EAP) termination and use the Challenge Handshake Authentication Protocol (CHAP) to communicate with the RADIUS server.

eap: Configures the access device to relay EAP packets, and supports any of the EAP authentication methods to communicate with the RADIUS server.

pap: Configures the access device to perform EAP termination and use the Password Authentication Protocol (PAP) to communicate with the RADIUS server.

Usage guidelines

The access device terminates or relays EAP packets.

· In EAP termination mode—The access device re-encapsulates and sends the authentication data from the client in standard RADIUS packets to the RADIUS server. The device performs either CHAP or PAP authentication with the RADIUS server. In this mode, the RADIUS server supports only MD5-Challenge EAP authentication and the username and password EAP authentication initiated by an iNode client.

¡ PAP transports usernames and passwords in plain text. The authentication method applies to scenarios that do not require high security. To use PAP, the client can be an iNode 802.1X client.

¡ CHAP transports usernames in plain text and passwords in encrypted form over the network. CHAP is more secure than PAP.

· In EAP relay mode—The access device relays EAP messages between the client and the RADIUS server. The EAP relay mode supports multiple EAP authentication methods, such as MD5-Challenge, EAP-TLS, and PEAP. To use this mode, make sure the RADIUS server meets the following requirements:

¡ Supports the EAP-Message and Message-Authenticator attributes.

¡ Uses the same EAP authentication method as the client.

If this mode is used, the user-name-format command configured in RADIUS scheme view does not take effect. For more information about the user-name-format command, see "RADIUS commands."

If RADIUS authentication is used, you must configure the access device to use the same authentication method (PAP, CHAP, or EAP) as the RADIUS server.

Examples

# Enable the access device to terminate EAP packets and perform PAP authentication with the RADIUS server.

<Sysname> system-view

[Sysname] dot1x authentication-method pap

Related commands

display dot1x

dot1x auth-fail eapol

Use dot1x auth-fail eapol to enable the device to send an EAP-Success packet to a client when the client user is assigned to the 802.1X Auth-Fail VLAN or VSI on a port.

Use undo dot1x auth-fail eapol to restore the default.

Syntax

dot1x auth-fail eapol

undo dot1x auth-fail eapol

Default

The device sends an EAP-Failure packet to a client when the client user is assigned to the 802.1X Auth-Fail VLAN or VSI on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

Some 802.1X clients cannot send DHCP requests for IP addresses after they receive EAP-Failure packets. To have these clients obtain IP addresses to access authorized resources after they are assigned to the 802.1X Auth-Fail VLAN or VSI, use this feature.

Examples

# Enable the device to send an EAP-Success packet to a client when the client user is assigned to the 802.1X Auth-Fail VLAN or VSI on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x auth-fail eapol

Related commands

dot1x auth-fail vlan

dot1x auth-fail vsi

dot1x auth-fail vlan

Use dot1x auth-fail vlan to configure an 802.1X Auth-Fail VLAN on a port.

Use undo dot1x auth-fail vlan to restore the default.

Syntax

dot1x auth-fail vlan authfail-vlan-id

undo dot1x auth-fail vlan

Default

No 802.1X Auth-Fail VLAN exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

authfail-vlan-id: Specifies the ID of the 802.1X Auth-Fail VLAN on the port. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created. If the port type is hybrid, verify that the VLAN to be specified as the Auth-Fail VLAN is not in the tagged VLAN list on the port.

Usage guidelines

An 802.1X Auth-Fail VLAN accommodates users that have failed 802.1X authentication for any reason other than unreachable servers. Users in the Auth-Fail VLAN can access a limited set of network resources.

You cannot specify a VLAN as both a super VLAN and an 802.1X Auth-Fail VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

On a port, the 802.1X Auth-Fail VLAN configuration is mutually exclusive with the 802.1X guest VSI, 802.1X Auth-Fail VSI, and 802.1X critical VSI settings.

To delete a VLAN that has been configured as an 802.1X Auth-Fail VLAN, you must first use the undo dot1x auth-fail vlan command.

Examples

# Configure VLAN 100 as the Auth-Fail VLAN on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x auth-fail vlan 100

Related commands

display dot1x

dot1x auth-fail vsi

Use dot1x auth-fail vsi to configure an 802.1X Auth-Fail VSI on a port.

Use undo dot1x auth-fail vsi to restore the default.

Syntax

dot1x auth-fail vsi authfail-vsi-name

undo dot1x auth-fail vsi

Default

No 802.1X Auth-Fail VSI exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

authfail-vsi-name: Specifies the name of the 802.1X Auth-Fail VSI on the port, a case-sensitive string of 1 to 31 characters.

Usage guidelines

This command is supported only on 802.1X-enabled ports that perform MAC-based access control.

An 802.1X Auth-Fail VSI accommodates users that have failed 802.1X authentication for any reason other than unreachable servers. Users in the 802.1X Auth-Fail VSI can access a limited set of network resources in the VXLAN associated with this VSI.

You can configure only one 802.1X Auth-Fail VSI on a port. The 802.1X Auth-Fail VSIs on different ports can be different.

On a port, the 802.1X Auth-Fail VSI configuration is mutually exclusive with the 802.1X guest VLAN, 802.1X Auth-Fail VLAN, and 802.1X critical VLAN settings.

Examples

# Specify VSI vsiuser as the Auth-Fail VSI on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x auth-fail vsi vsiuser

Related commands

display dot1x

dot1x critical eapol

Use dot1x critical eapol to enable the sending of an EAP-Success packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN or VSI on a port.

Use undo dot1x critical eapol to restore the default.

Syntax

dot1x critical eapol

undo dot1x critical eapol

Default

The device sends an EAP-Failure packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN or VSI on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

By default, the device sends EAP-Failure packets to 802.1X clients when the client users are assigned to the 802.1X critical VLAN or VSI. Some 802.1X clients, for example, Windows built-in 802.1X clients, cannot respond to the EAP-Request/Identity packets from the device for reauthentication if they have received an EAP-Failure packet. As a result, reauthentication for these clients will fail after the authentication server becomes reachable.

To avoid this situation, enable the device to send EAP-Success packets instead of EAP-Failure packets to 802.1X clients when the client users are assigned to the 802.1X critical VLAN or VSI.

Examples

# Send an EAP-Success packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN or VSI on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x critical eapol

Related commands

dot1x critical vlan

dot1x critical vsi

dot1x critical vlan

Use dot1x critical vlan to configure an 802.1X critical VLAN on a port.

Use undo dot1x critical vlan to restore the default.

Syntax

dot1x critical vlan critical-vlan-id

undo dot1x critical vlan

Default

No 802.1X critical VLAN exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

critical-vlan-id: Specifies the ID of the 802.1X critical VLAN on the port. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created. If the port type is hybrid, verify that the VLAN to be specified as the critical VLAN is not in the tagged VLAN list on the port.

Usage guidelines

An 802.1X critical VLAN accommodates users that fail 802.1X authentication because all the RADIUS servers in their ISP domains are unreachable. Users in the critical VLAN can access a limited set of network resources depending on the configuration.

You cannot specify a VLAN as both a super VLAN and an 802.1X critical VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

On a port, the 802.1X critical VLAN configuration is mutually exclusive with the 802.1X guest VSI, 802.1X Auth-Fail VSI, and 802.1X critical VSI settings.

To delete a VLAN that has been configured as an 802.1X critical VLAN, you must first use the undo dot1x critical vlan command.

Examples

# Specify VLAN 100 as the 802.1X critical VLAN on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x critical vlan 100

Related commands

display dot1x

dot1x critical vsi

Use dot1x critical vsi to configure an 802.1X critical VSI on a port.

Use undo dot1x critical vsi to restore the default.

Syntax

dot1x critical vsi critical-vsi-name

undo dot1x critical vsi

Default

No 802.1X critical VSI exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

critical-vsi-name: Specifies the name of the 802.1X critical VSI on the port, a case-sensitive string of 1 to 31 characters.

Usage guidelines

This command is supported only on 802.1X-enabled ports that perform MAC-based access control.

An 802.1X critical VSI accommodates users that have failed 802.1X authentication because all the RADIUS servers in their ISP domains are unreachable. Users in the 802.1X critical VSI can access a limited set of network resources in the VXLAN associated with this VSI.

You can configure only one 802.1X critical VSI on a port. The 802.1X critical VSIs on different ports can be different.

On a port, the 802.1X critical VSI configuration is mutually exclusive with the 802.1X guest VLAN, 802.1X Auth-Fail VLAN, and 802.1X critical VLAN settings.

Examples

# Specify VSI vsiuser as the 802.1X critical VSI on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x critical vsi vsiuser

Related commands

display dot1x

dot1x critical-voice-vlan

Use dot1x critical-voice-vlan to enable the 802.1X critical voice VLAN feature on a port.

Use undo dot1x critical-voice-vlan to restore the default.

Syntax

dot1x critical-voice-vlan

undo dot1x critical-voice-vlan

Default

The 802.1X critical voice VLAN feature is disabled on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The 802.1X critical voice VLAN on a port accommodates 802.1X voice users that have failed authentication because none of the RADIUS servers in their ISP domain are reachable.

Before you enable the 802.1X critical voice VLAN feature on the port, make sure the following requirements are met:

· The port is configured with the voice VLAN.

To configure a voice VLAN on a port, use the voice-vlan enable command (see Layer 2—LAN Switching Command Reference).

· LLDP is enabled both globally and on the port.

The device uses LLDP to identify voice users. For information about LLDP commands, see Layer 2—LAN Switching Command Reference.

· An 802.1X critical VLAN is configured on the port. This setting ensures that a voice user is assigned to the critical VLAN if it has failed authentication for unreachability of RADIUS servers before the device recognizes it as a voice user. If an 802.1X critical VLAN is not available, the voice user might be logged off instead.

Examples

# Enable the 802.1X critical voice VLAN feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x critical-voice-vlan

Related commands

display dot1x

lldp enable (Layer 2—LAN Switching Command Reference)

lldp global enable (Layer 2—LAN Switching Command Reference)

voice-vlan enable (Layer 2—LAN Switching Command Reference)

dot1x domain-delimiter

Use dot1x domain-delimiter to specify a set of domain name delimiters supported by the device.

Use undo dot1x domain-delimiter to restore the default.

Syntax

dot1x domain-delimiter string

undo dot1x domain-delimiter

Default

The device supports only the at sign (@) delimiter for 802.1X users.

Views

System view

Predefined user roles

network-admin

Parameters

string: Specifies a set of 1 to 16 domain name delimiters for 802.1X users. No space is required between delimiters. Available delimiters include the at sign (@), backslash (\), dot (.), and forward slash (/). If you want to use backslash (\) as the domain name delimiter, you must enter the escape character (\) along with the backslash (\) sign.

Usage guidelines

Any character in the configured set can be used as the domain name delimiter for 802.1X authentication users. Usernames that include domain names can use the format of username@domain-name, domain-name\username, username.domain-name, or username/domain-name.

The delimiter set you configured overrides the default setting. If the at sign (@) is not included in the delimiter set, the device does not support the 802.1X users that use this sign as the domain name delimiter.

If a username string contains multiple configured delimiters, the device takes the rightmost delimiter in the username string as the domain name delimiter. For example, if you configure the forward slash (/), dot (.), and backslash (\) as delimiters, the domain name delimiter for the username string 121.123/22\@abc is the backslash (\). The username is @abc and the domain name is 121.123/22.

Examples

# Specify the at sign (@) and forward slash (/) as domain name delimiters.

<Sysname> system-view

[Sysname] dot1x domain-delimiter @/

Related commands

display dot1x

dot1x ead-assistant enable

Use dot1x ead-assistant enable to enable the EAD assistant feature.

Use undo dot1x ead-assistant enable to disable the EAD assistant feature.

Syntax

dot1x ead-assistant enable

undo dot1x ead-assistant enable

Default

The EAD assistant feature is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The EAD assistant feature enables the access device to redirect the HTTP or HTTPS requests of a user to a URL to download and install EAD client. This feature eliminates the tedious job of the administrator to deploy EAD clients.

For the EAD assistant feature to take effect on a port, you must set the port authorization mode to auto.

The feature is mutually exclusive with MAC authentication and port security. You must disable MAC authentication and port security globally before you enable the EAD assistant feature.

To redirect the HTTPS requests of 802.1X users, you must execute the dot1x ead-assistant url command. By default, the device listens to port 6654 for HTTPS requests to be redirected. To change the redirect listening port number, see configuring HTTP redirect in Layer 3—IP Services Configuration Guide.

Examples

# Enable the EAD assistant feature.

<Sysname> system-view

[Sysname] dot1x ead-assistant enable

Related commands

display dot1x

dot1x ead-assistant free-ip

dot1x ead-assistant url

http-redirect https-port (Layer 3—IP Services Command Reference)

dot1x ead-assistant free-ip

Use dot1x ead-assistant free-ip to configure a free IP.

Use undo dot1x ead-assistant free-ip to remove the specified or all free IP addresses.

Syntax

dot1x ead-assistant free-ip ip-address { mask-address | mask-length }

undo dot1x ead-assistant free-ip { ip-address { mask-address | mask-length } | all }

Default

No free IPs exist. Users cannot access any segments before they pass 802.1X authentication.

Views

System view

Predefined user roles

network-admin

Parameters

ip-address: Specifies a freely accessible IP address segment, also called a free IP.

mask: Specifies an IP address mask.

mask-length: Specifies IP address mask length in the range of 1 to 32.

all: Removes all free IP addresses.

Usage guidelines

With EAD assistant enabled on the device, unauthenticated 802.1X users can access the network resources in the free IP segments before they pass 802.1X authentication.

Execute this command multiple times to configure multiple free IPs.

Examples

# Configure 192.168.1.1/16 as a free IP.

<Sysname> system-view

[Sysname] dot1x ead-assistant free-ip 192.168.1.1 255.255.0.0

Related commands

display dot1x

dot1x ead-assistant enable

dot1x ead-assistant url

Use dot1x ead-assistant url to configure a redirect URL for EAD assistant.

Use undo dot1x ead-assistant url to restore the default.

Syntax

dot1x ead-assistant url url-string

undo dot1x ead-assistant url

Default

No redirect URL exists for EAD assistant.

Views

System view

Predefined user roles

network-admin

Parameters

url-string: Specifies the redirect URL, a case-sensitive string of 1 to 64 characters in the format http://string or https://string. If the specified URL does not start with http:// or https://, the device prefixes the specified URL with http://. Because the URL string can contain question marks (?), you cannot obtain help information by entering a question mark at the position of this argument.

Usage guidelines

When an unauthenticated user uses a Web browser to access any network other than the free IP, the device redirects the HTTP or HTTPS requests of the user to the redirect URL.

The redirect URL must be on the free IP subnet.

If you execute this command multiple times, the most recent configuration takes effect.

By default, the device listens to port 6654 for HTTPS requests to be redirected. To change the redirect listening port number, see configuring HTTP redirect in Layer 3—IP Services Configuration Guide.

Examples

# Configure the redirect URL as http://test.com.

<Sysname> system-view

[Sysname] dot1x ead-assistant url http://test.com

Related commands

display dot1x

dot1x ead-assistant enable

dot1x ead-assistant free-ip

http-redirect https-port (Layer 3—IP Services Command Reference)

dot1x eap-tls-fragment to-server

Use dot1x eap-tls-fragment to-server to enable 802.1X EAP-TLS fragmentation and set the maximum EAP-TLS fragment size.

Use undo dot1x eap-tls-fragment to-server to restore the default.

Syntax

dot1x eap-tls-fragment to-server eap-tls-max-length

undo dot1x eap-tls-fragment to-server

Default

EAP-TLS messages are not fragmented.

Views

System view

Predefined user roles

network-admin

Parameters

eap-tls-max-length: Sets the maximum EAP-TLS fragment size in bytes. The value range is 100 to 1500.

Usage guidelines

802.1X EAP-TLS fragmentation takes effect only when EAP relay mode is used.

When the device uses EAP-TLS authentication method in EAP relay mode, the RADIUS packets might exceed the maximum packet size supported by the RADIUS server. This situation typically occurs when long EAP-TLS messages are encapsulated in the EAP-Message attribute of the RADIUS packet sent to the RADIUS server.

To avoid authentication failures caused by oversized packets, fragment the EAP-TLS messages depending on the maximum RADIUS packet size supported by the remote RADIUS server.

For example, the maximum packet length allowed by the server is 1200 bytes and the length of a RADIUS packet (excluding the EAP-Message attribute) is 800 bytes. To make sure the maximum length of a RADIUS packet does not exceed 1200 bytes, you must set the maximum length of an EAP-TLS fragment to a value less than 400 bytes.

Examples

# Set the maximum EAP-TLS fragment size to 400 bytes.

<Sysname> system-view

[Sysname] dot1x eap-tls-fragment to-server 400

Related commands

display dot1x

dot1x authentication-method

dot1x eapol untag

Use dot1x eapol untag to enable the device to remove the VLAN tags of all 802.1X protocol packets sent out of a port to 802.1X clients.

Use undo dot1x eapol untag to restore the default.

Syntax

dot1x eapol untag

undo dot1x eapol untag

Default

Whether the device removes the VLAN tags of all 802.1X protocol packets sent out of a port to 802.1X clients depends on the configuration in the VLAN module.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

This command removes the VLAN tags of all 802.1X protocol packets sent out of the port to 802.1X clients. Do not use this command if VLAN-aware 802.1X clients are attached to the port. As a best practice, use this command only in the scenario described in the command usage guidelines.

This command operates on a hybrid port to have it send 802.1X protocol packets with their VLAN tags removed, regardless of whether the port is a tagged or untagged member of a VLAN.

Use this command if the 802.1X-enabled hybrid port is a tagged member of its PVID and the attached 802.1X clients cannot recognize VLAN-tagged 802.1X protocol packets.

Examples

# Enable the device to remove the VLAN tags of all 802.1X protocol packets sent out of Twenty-FiveGigE 1/0/1 to 802.1X clients.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x eapol untag

Related commands

display dot1x

dot1x guest-vlan

Use dot1x guest-vlan to configure an 802.1X guest VLAN on a port.

Use undo dot1x guest-vlan to restore the default.

Syntax

dot1x guest-vlan guest-vlan-id

undo dot1x guest-vlan

Default

No 802.1X guest VLAN exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

guest-vlan-id: Specifies the ID of the 802.1X guest VLAN. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created. If the port type is hybrid, verify that the VLAN to be specified as the guest VLAN is not in the tagged VLAN list on the port.

Usage guidelines

An 802.1X guest VLAN accommodates users that have not performed 802.1X authentication. In the guest VLAN, users can access a limited set of network resources, such as a software server, to download anti-virus software and system patches.

You cannot specify a VLAN as both a super VLAN and an 802.1X guest VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

On a port, the 802.1X guest VLAN configuration is mutually exclusive with the 802.1X guest VSI, 802.1X Auth-Fail VSI, and 802.1X critical VSI settings.

To delete a VLAN that has been configured as a guest VLAN, you must use the undo dot1x guest-vlan command first.

Examples

# Specify VLAN 100 as the 802.1X guest VLAN on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x guest-vlan 100

Related commands

display dot1x

dot1x guest-vlan-delay

Use dot1x guest-vlan-delay to enable 802.1X guest VLAN assignment delay on a port.

Use undo dot1x guest-vlan-delay to disable the specified 802.1X guest VLAN assignment delay on a port.

Syntax

dot1x guest-vlan-delay { eapol | new-mac }

undo dot1x guest-vlan-delay [ eapol | new-mac ]

Default

802.1X guest VLAN assignment delay is disabled on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

eapol: Specifies EAPOL-triggered 802.1X guest VLAN assignment delay. This keyword takes effect if 802.1X authentication is triggered by EAPOL-Start packets.

new-mac: Specifies new MAC-triggered 802.1X guest VLAN assignment delay. This keyword takes effect if 802.1X authentication is triggered by packets from unknown MAC addresses.

Usage guidelines

This command enables the device to delay assigning an 802.1X-enabled port to the 802.1X guest VLAN when 802.1X authentication is triggered on the port.

To use this feature, the 802.1X-enabled port must perform MAC-based access control.

When 802.1X authentication is triggered on a port, the device performs the following operations:

1. Sends a unicast EAP-Request/Identity packet to the MAC address that triggers the authentication.

2. Retransmits the packet if no response has been received within the username request timeout interval set by using the dot1x timer tx-period command.

3. Assigns the port to the 802.1X guest VLAN after the maximum number of request attempts set by using the dot1x retry command is reached.

If you use the undo command without any keyword, the command disables both EAPOL-triggered and new MAC-triggered 802.1X guest VLAN assignment delay on a port.

Examples

# Enable EAPOL-triggered 802.1X guest VLAN assignment delay on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x guest-vlan-delay eapol

Related commands

display dot1x

dot1x guest-vlan

dot1x retry

dot1x timer tx-period

dot1x guest-vsi

Use dot1x guest-vsi to configure an 802.1X guest VSI on a port.

Use undo dot1x guest-vsi to restore the default.

Syntax

dot1x guest-vsi guest-vsi-name

undo dot1x guest-vsi

Default

No 802.1X guest VSI exists on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

guest-vsi-name: Specifies the name of the 802.1X guest VSI on the port, a case-sensitive string of 1 to 31 characters.

Usage guidelines

This command is supported only on 802.1X-enabled ports that perform MAC-based access control.

An 802.1X guest VSI accommodates users that have not performed 802.1X authentication. Users in the 802.1X guest VSI can access a limited set of network resources in the VXLAN associated with this VSI. For example, an 802.1X user can access a software server to download anti-virus software and system patches.

You can configure only one 802.1X guest VSI on a port. The 802.1X guest VSIs on different ports can be different.

On a port, the 802.1X guest VSI configuration is mutually exclusive with the 802.1X guest VLAN, 802.1X Auth-Fail VLAN, and 802.1X critical VLAN settings.

Examples

# Specify VSI vsiuser as the 802.1X guest VSI on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x guest-vsi vsiuser

Related commands

display dot1x

reset dot1x guest-vsi

dot1x guest-vsi-delay

Use dot1x guest-vsi-delay to enable 802.1X guest VSI assignment delay on a port.

Use undo dot1x guest-vsi-delay to disable the specified 802.1X guest VSI assignment delay on a port.

Syntax

dot1x guest-vsi-delay { eapol | new-mac }

undo dot1x guest-vsi-delay [ eapol | new-mac ]

Default

802.1X guest VSI assignment delay is disabled on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

eapol: Specifies EAPOL-triggered 802.1X guest VSI assignment delay. This keyword takes effect if 802.1X authentication is triggered by EAPOL-Start packets.

new-mac: Specifies new MAC-triggered 802.1X guest VSI assignment delay. This keyword takes effect if 802.1X authentication is triggered by packets from unknown MAC addresses.

Usage guidelines

This command enables the device to delay assigning an 802.1X-enabled port to the 802.1X guest VSI when 802.1X authentication is triggered on the port.

To use this feature, the 802.1X-enabled port must perform MAC-based access control.

When 802.1X authentication is triggered on a port, the device performs the following operations:

1. Sends a unicast EAP-Request/Identity packet to the MAC address that triggers the authentication.

2. Retransmits the packet if no response has been received within the username request timeout interval set by using the dot1x timer tx-period command.

3. Assigns the port to the 802.1X guest VSI after the maximum number of request attempts set by using the dot1x retry command is reached.

If you use the undo command without any keyword, the command disables both EAPOL-triggered and new MAC-triggered 802.1X guest VSI assignment delays on a port.

Examples

# Enable EAPOL-triggered 802.1X guest VSI assignment delay on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x guest-vsi-delay eapol

Related commands

display dot1x

dot1x guest-vsi

dot1x retry

dot1x timer tx-period

dot1x handshake

Use dot1x handshake to enable the online user handshake feature.

Use undo dot1x handshake to disable the online user handshake feature.

Syntax

dot1x handshake

undo dot1x handshake

Default

The online user handshake feature is enabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The online user handshake feature enables the device to periodically send EAP-Request/Identity packets to the client for verifying the connectivity status of online 802.1X users. The device sets a user to the offline state if it does not receive an EAP-Response/Identity packet from the user after making the maximum attempts within the handshake period. To set the handshake timer, use the dot1x timer handshake-period command. To set the maximum handshake attempts, use the dot1x retry command.

As a best practice to ensure online user handshake and new user authentication when a large number of users are present, set the following parameters to a large value:

· Handshake timer (set by using the dot1x timer handshake-period command).

· Maximum number of attempts to send an authentication request to a client (set by using the dot1x retry command).

Examples

# Enable the online user handshake feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x handshake

Related commands

display dot1x

dot1x timer handshake-period

dot1x retry

dot1x handshake reply enable

Use dot1x handshake reply enable to enable the 802.1X online user handshake reply feature.

Use undo dot1x handshake reply enable to disable the 802.1X online user handshake reply feature.

Syntax

dot1x handshake reply enable

undo dot1x handshake reply enable

Default

The 802.1X online user handshake reply feature is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to reply to 802.1X clients' EAP-Response/Identity packets with EAP-Success packets during the online handshake process.

Use this command only if 802.1X clients will go offline without receiving EAP-Success packets from the device.

Examples

# Enable the 802.1X online user handshake reply feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x handshake reply enable

Related commands

dot1x handshake

dot1x handshake secure

Use dot1x handshake secure to enable the online user handshake security feature.

Use undo dot1x handshake secure to disable the online user handshake security feature.

Syntax

dot1x handshake secure

undo dot1x handshake secure

Default

The online user handshake security feature is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The online user handshake security feature is applicable only to the network that deploys the iNode client and IMC server for 802.1X authentication. It prevents users from using illegal client software to bypass iNode security check.

To have this feature take effect, make sure the online user handshake feature is enabled.

Examples

# Enable the online user handshake security feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x handshake secure

Related commands

display dot1x

dot1x handshake

dot1x mac-binding

Use dot1x mac-binding to add an 802.1X MAC address binding entry.

Use undo dot1x mac-binding to delete the specified 802.1X MAC address binding entries.

Syntax

dot1x mac-binding mac-address

undo dot1x mac-binding { mac-address | all }

Default

No 802.1X MAC address binding entries exist on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H, excluding broadcast, multicast, and all-zero MAC addresses.

all: Specifies all MAC addresses that are bound to a port.

Usage guidelines

This command takes effect only when the 802.1X MAC address binding feature takes effect.

802.1X MAC address binding entries, both manually added and automatically generated, never age out. They can survive a user logoff or a device reboot. To delete an entry, use the undo dot1x mac-binding mac-address command. An 802.1X MAC address binding entry cannot be deleted when the user in the entry is online.

After the number of 802.1X MAC address binding entries reaches the upper limit of concurrent 802.1X users (set by using the dot1x max-user command), the following restrictions exist:

· Users not in the binding entries will fail authentication even after users in the binding entries go offline.

· New 802.1X MAC address binding entries are not allowed.

Examples

# Add an 802.1X MAC address binding entry on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x mac-binding 000a-eb29-75f1

Related commands

dot1x

dot1x mac-binding enable

dot1x port-method

dot1x mac-binding enable

Use dot1x mac-binding enable to enable the 802.1X MAC address binding feature.

Use undo dot1x mac-binding enable to disable the 802.1X MAC address binding feature.

Syntax

dot1x mac-binding enable

undo dot1x mac-binding enable

Default

The 802.1X MAC address binding feature is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only on a port that performs MAC-based access control.

The 802.1X MAC address binding feature automatically binds MAC addresses of authenticated 802.1X users to the users' access port and generates 802.1X MAC address binding entries.

802.1X MAC address binding entries, both automatically generated and manually added, never age out. They can survive a user logoff or a device reboot. To delete an entry, use the undo dot1x mac-binding mac-address command. An 802.1X MAC address binding entry cannot be deleted when the user in the entry is online.

After the number of 802.1X MAC address binding entries reaches the upper limit of concurrent 802.1X users (set by using the dot1x max-user command), the following restrictions exist:

· Users not in the binding entries will fail authentication even after users in the binding entries go offline.

· New 802.1X MAC address binding entries are not allowed.

Examples

# Enable 802.1X MAC address binding on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x mac-binding enable

Related commands

dot1x

dot1x mac-binding

dot1x port-method

dot1x mandatory-domain

Use dot1x mandatory-domain to specify a mandatory 802.1X authentication domain on a port.

Use undo dot1x mandatory-domain to restore the default.

Syntax

dot1x mandatory-domain domain-name

undo dot1x mandatory-domain

Default

No mandatory 802.1X authentication domain is specified on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

domain-name: Specifies the ISP domain name, a case-insensitive string of 1 to 255 characters.

Usage guidelines

When the system authenticates an 802.1X user trying to access a port, it selects an authentication domain in the following order:

1. Mandatory domain.

2. ISP domain specified in the username.

3. Default ISP domain.

Examples

# Specify my-domain as the mandatory authentication domain for 802.1X users on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x mandatory-domain my-domain

Related commands

display dot1x

dot1x max-user

Use dot1x max-user to set the maximum number of concurrent 802.1X users on a port.

Use undo dot1x max-user to restore the default.

Syntax

dot1x max-user max-number

undo dot1x max-user

Default

A port allows a maximum of 4294967295 concurrent 802.1X users.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of concurrent 802.1X users on a port. The value range is 1 to 4294967295.

Usage guidelines

Set the maximum number of concurrent 802.1X users on a port to prevent the system resources from being overused. When the maximum number is reached, the port denies subsequent 802.1X users.

Examples

# Set the maximum number of concurrent 802.1X users to 32 on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x max-user 32

Related commands

display dot1x

dot1x multicast -trigger

Use dot1x multicast-trigger to enable the 802.1X multicast trigger feature.

Use undo dot1x multicast-trigger to disable the 802.1X multicast trigger feature.

Syntax

dot1x multicast-trigger

undo dot1x multicast-trigger

Default

The 802.1X multicast trigger feature is enabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The multicast trigger feature enables the device to act as the initiator. The device periodically multicasts EAP-Request/Identity packets out of a port to detect 802.1X clients and trigger authentication. You can use the dot1x timer tx-period command to set the interval for sending multicast EAP-Request/Identity packets.

As a best practice to conserve link bandwidth, disable the multicast trigger if a lot of VLANs are configured on the port.

Examples

# Enable the multicast trigger feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x multicast-trigger

Related commands

display dot1x

dot1x timer tx-period

dot1x unicast-trigger

dot1x offline-detect enable

Use dot1x offline-detect enable to enable 802.1X offline detection on a port.

Use undo dot1x offline-detect enable to disable 802.1X offline detection.

Syntax

dot1x offline-detect enable

undo dot1x offline-detect enable

Default

802.1X offline detection is disabled on a port.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The 802.1X offline detection feature monitors the online status of 802.1X users. This feature uses an offline detect timer to set the interval that the device must wait for traffic from a user before the device determines that the user is idle. If the device has not received traffic from a user before the timer expires, the device logs off that user and requests the accounting server to stop accounting for the user.

To have 802.1X offline detection take effect, you must configure the port to perform MAC-based access control. If you change the port access mode to port-based, the 802.1X offline detection feature cannot take effect.

To set the offline detect timer, use the dot1x timer command.

Examples

# Disable 802.1X offline detection on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] undo dot1x offline-detect enable

Related commands

display dot1x

dot1x port-method

dot1x timer

dot1x port-control

Use dot1x port-control to set the authorization state for the port.

Use undo dot1x port-control to restore the default.

Syntax

dot1x port-control { authorized-force | auto | unauthorized-force }

undo dot1x port-control

Default

The default port authorization state is auto.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

authorized-force: Places the port in authorized state, enabling users on the port to access the network without authentication.

auto: Places the port initially in unauthorized state to allow only EAPOL packets to pass, and places the port in authorized state after a user passes authentication. You can use this option in most scenarios.

unauthorized-force: Places the port in unauthorized state, denying any access requests from users on the port.

Usage guidelines

You can use this command to set the port authorization state to determine whether a client is granted access to the network.

Examples

# Set the authorization state of Twenty-FiveGigE 1/0/1 to unauthorized-force.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x port-control unauthorized-force

Related commands

display dot1x

dot1x port-method

Use dot1x port-method to specify an access control method for the port.

Use undo dot1x port-method to restore the default.

Syntax

dot1x port-method { macbased | portbased }

undo dot1x port-method

Default

MAC-based access control applies.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

macbased: Uses MAC-based access control on the port to separately authenticate each user attempting to access the network. Using this method, when an authenticated user logs off, no other online users are affected.

portbased: Uses port-based access control on the port. Using this method, once an 802.1X user passes authentication on the port, any subsequent user can access the network through the port without authentication. When the authenticated user logs off, all other users are logged off.

Usage guidelines

CAUTION:

If online 802.1X users are present on a port, changing its access control method will cause the online users to go offline.

MAC-based access control provides higher security than port-based access control.

Examples

# Configure Twenty-FiveGigE 1/0/1 to implement port-based access control.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x port-method portbased

Related commands

display dot1x

dot1x quiet-period

Use dot1x quiet-period to enable the quiet timer.

Use undo dot1x quiet-period to disable the quiet timer.

Syntax

dot1x quiet-period

undo dot1x quiet-period

Default

The quiet timer is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When a client fails 802.1X authentication, the device must wait a period of time before it can process authentication requests from the client. You can use the dot1x timer quiet-period command to set the quiet timer.

Examples

# Enable the quiet timer and set the quiet timer to 100 seconds.

<Sysname> system-view

[Sysname] dot1x quiet-period

[Sysname] dot1x timer quiet-period 100

Related commands

display dot1x

dot1x timer

dot1x re-authenticate

Use dot1x re-authenticate to enable the 802.1X periodic reauthentication feature.

Use undo dot1x re-authenticate to disable the 802.1X periodic reauthentication feature.

Syntax

dot1x re-authenticate

undo dot1x re-authenticate

Default

The 802.1X periodic reauthentication feature is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

Periodic reauthentication enables the access device to periodically authenticate online 802.1X users on a port. This feature tracks the connection status of online users and updates the authorization attributes assigned by the server, such as the ACL and VLAN.

You can use the dot1x timer reauth-period command to configure the interval for reauthentication.

If periodic reauthentication is triggered for a user while that user is waiting for online synchronization, the system performs online synchronization and does not perform reauthentication for the user.

Examples

# Enable the 802.1X periodic reauthentication feature on Twenty-FiveGigE 1/0/1, and set the periodic reauthentication interval to 1800 seconds.

<Sysname> system-view

[Sysname] dot1x timer reauth-period 1800

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x re-authenticate

Related commands

display dot1x

dot1x server-recovery online-user-sync

dot1x timer

dot1x re-authenticate manual

Use dot1x re-authenticate manual to manually reauthenticate all online 802.1X users on a port.

Syntax

dot1x re-authenticate manual

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

After this command is executed, this device reauthenticates all online 802.1X users on a port. The command takes effect regardless of the server-assigned reauthentication attribute and the periodic reauthentication feature.

Examples

# Manually reauthenticate all online 802.1X users on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x re-authenticate manual

Related commands

dot1x re-authenticate

dot1x re-authenticate server-unreachable keep-online

Use dot1x re-authenticate server-unreachable keep-online to enable the keep-online feature on a port.

Use undo dot1x re-authenticate server-unreachable to restore the default.

Syntax

dot1x re-authenticate server-unreachable keep-online

undo dot1x re-authenticate server-unreachable

Default

The keep-online feature is disabled on a port. The device logs off online 802.1X authenticated users if no server is reachable for 802.1X reauthentication.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This feature keeps authenticated 802.1X users online when no server is reachable for 802.1X reauthentication.

Examples

# Enable the keep-online feature on Twenty-FiveGigE 1/0/1 for 802.1X reauthentication.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x re-authenticate server-unreachable keep-online

Related commands

display dot1x

dot1x re-authenticate

dot1x retry

Use dot1x retry to set the maximum number of attempts for sending an authentication request to a client.

Use undo dot1x retry to restore the default.

Syntax

dot1x retry retries

undo dot1x retry

Default

A maximum of two attempts are made to send an authentication request to a client.

Views

System view

Predefined user roles

network-admin

Parameters

retries: Specifies the maximum number of attempts for sending an authentication request to a client. The value range is 1 to 10.

Usage guidelines

The access device retransmits an authentication request to a client in any of the following situations:

· The device does not receive any responses from the client within the username request timeout interval. The timer is set by using the dot1x timer tx-period tx-period-value command for the EAP-Request/Identity packet.

· The device does not receive any responses from the client within the client timeout interval. The timer is set by using the dot1x timer supp-timeout supp-timeout-value command for the EAP-Request/MD5-Challenge packet.

The access device stops retransmitting the request, if it has made the maximum number of request transmission attempts but still received no response.

Examples

# Set the maximum number of attempts to 9 for sending an authentication request to a client.

<Sysname> system-view

[Sysname] dot1x retry 9

Related commands

display dot1x

dot1x timer

dot1x server-recovery online-user-sync

Use dot1x server-recovery online-user-sync to enable 802.1X online user synchronization.

Use undo dot1x server-recovery online-user-sync to disable 802.1X online user synchronization.

Syntax

dot1x server-recovery online-user-sync

undo dot1x server-recovery online-user-sync

Default

802.1X online user synchronization is disabled. The device does not synchronize online 802.1X user information on a port with a RADIUS server after the RADIUS server recovers from the unreachable state.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

IMPORTANT:

This command takes effect only when the device uses an IMC RADIUS server to authenticate 802.1X users.

‌

To ensure that the RADIUS server maintains the same online 802.1X user information as the device after the server state changes from unreachable to reachable, use this feature.

This feature synchronizes online 802.1X user information between the device and the RADIUS server when the RADIUS server state is detected having changed from unreachable to reachable.

When synchronizing online 802.1X user information on a port with the RADIUS server, the device initiates 802.1X authentication in turn for each authenticated online 802.1X user to the RADIUS server.

If synchronization fails for an online user, the device logs off that user unless the failure occurs because the server has become unreachable again.

The amount of time required to complete online user synchronization increases as the number of online users grows. This might result in an increased delay for new 802.1X users and users in the critical VLAN or VSI to authenticate or reauthenticate to the RADIUS server and come online.

To have this feature take effect, you must use it in conjunction with the RADIUS server status detection feature, which is configurable with the radius-server test-profile command. When you configure this feature, make sure the detection interval is shorter than the RADIUS server quiet timer configured by using the timer quiet command in RADIUS scheme view. The server state changes to active on expiration of the quiet timer regardless of its actual reachability. Setting a shorter detection interval than the quiet timer prevents the RADIUS server status detection feature from falsely reporting the server reachability.

For more information about the RADIUS server status detection feature, see AAA configuration in Security Configuration Guide.

Examples

# Enable 802.1X online user synchronization on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x server-recovery online-user-sync

Related commands

display dot1x

radius-server test-profile

timer quiet (RADIUS scheme view)

dot1x timer

Use dot1x timer to set an 802.1X timer.

Use undo dot1x timer to restore the default of an 802.1X timer.

Syntax

dot1x timer { ead-timeout ead-timeout-value | handshake-period handshake-period-value | offline-detect offline-detect-value | quiet-period quiet-period-value | reauth-period reauth-period-value | server-timeout server-timeout-value | supp-timeout supp-timeout-value | tx-period tx-period-value | user-aging { auth-fail-vlan | auth-fail-vsi | critical-vlan | critical-vsi | guest-vlan | guest-vsi } aging-time-value }

undo dot1x timer { ead-timeout | handshake-period | offline-detect | quiet-period | reauth-period | server-timeout | supp-timeout | tx-period | user-aging { auth-fail-vlan | auth-fail-vsi | critical-vlan | critical-vsi | guest-vlan | guest-vsi } }

Default

The following 802.1X timers apply:

· EAD rule timer: 30 minutes.

· Handshake timer: 15 seconds.

· Offline detect timer: 300 seconds.

· Quiet timer: 60 seconds.

· Periodic reauthentication timer: 3600 seconds.

· Server timeout timer: 100 seconds.

· Client timeout timer: 30 seconds.

· Username request timeout timer: 30 seconds.

· User aging timers for all applicable types of 802.1X VLANs and VSIs: 1000 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

ead-timeout ead-timeout-value: Sets the EAD rule timer in minutes. The value range for the ead-timeout-value argument is 1 to 1440.

handshake-period handshake-period-value: Sets the handshake timer in seconds. The value range for the handshake-period-value argument is 5 to 1024.

offline-detect offline-detect-value: Sets the offline detect timer in seconds. The value range for the offline-detect-value argument is 60 to 2147483647.

quiet-period quiet-period-value: Sets the quiet timer in seconds. The value range for the quiet-period-value argument is 10 to 120.

reauth-period reauth-period-value: Sets the periodic reauthentication timer in seconds. The value range for the reauth-period-value argument is 60 to 7200.

server-timeout server-timeout-value: Sets the server timeout timer in seconds. The value range for the server-timeout-value argument is 100 to 300.

supp-timeout supp-timeout-value: Sets the client timeout timer in seconds. The value range for the supp-timeout-value argument is 1 to 120.

tx-period tx-period-value: Sets the username request timeout timer in seconds. The value range for the tx-period-value argument is 1 to 120.

user-aging: Sets the user aging timer for a type of 802.1X VLAN or VSI.

auth-fail-vlan: Specifies 802.1X Auth-Fail VLANs.

auth-fail-vsi: Specifies 802.1X Auth-Fail VSIs.

critical-vlan: Specifies 802.1X critical VLANs.

critical-vsi: Specifies 802.1X critical VSIs.

guest-vlan: Specifies 802.1X guest VLANs.

guest-vsi: Specifies 802.1X guest VSIs.

aging-time-value: Sets the user aging timer. The value range is 60 to 2147483647 seconds.

Usage guidelines

In most cases, the default settings are sufficient. You can edit the timers, depending on the network conditions.

· In a low-speed network, increase the client timeout timer.

· In a vulnerable network, set the quiet timer to a high value.

· In a high-performance network with quick authentication response, set the quiet timer to a low value.

· In a network with authentication servers of different performance, adjust the server timeout timer.

The network device uses the following 802.1X timers:

· EAD rule timer (ead-timeout)—Sets the lifetime of each EAD rule. When the timer expires or the user passes authentication, the rule is removed. If users fail to download the EAD client or fail to pass authentication before the timer expires, they must reconnect to the network to access the free IP.

· Handshake timer (handshake-period)—Sets the interval at which the access device sends client handshake requests to check the online status of a client that has passed authentication. If the device does not receive a response after sending the maximum number of handshake requests, it considers that the client has logged off.

· Offline detect timer (offline-detect)—Sets the interval that the device must wait for traffic from a user before the device determines that the user is idle. If the device has not received traffic from a user before the timer expires, the device logs off that user and requests the accounting server to stop accounting for the user. This timer takes effect only when the 802.1X offline detection feature is enabled.

· Quiet timer (quiet-period)—Starts when a client fails authentication. The access device must wait the time period before it can process the authentication attempts from the client.

· Periodic reauthentication timer (reauth-period)—Sets the interval at which the network device periodically reauthenticates online 802.1X users. To enable 802.1X periodic reauthentication on a port, use the dot1x re-authenticate command.

· Server timeout timer (server-timeout)—Starts when the access device sends a RADIUS Access-Request packet to the authentication server. If no response is received when this timer expires, the 802.1X authentication fails.

To avoid forced logoff before the server timeout timer expires, set the server timeout timer to a value that is lower than or equal to the product of the following values:

¡ The maximum number of RADIUS packet transmission attempts set by using the retry command in RADIUS scheme view.

¡ The RADIUS server response timeout timer set by using the timer response-timeout command in RADIUS scheme view.

For information about setting the maximum number of RADIUS packet transmission attempts and the RADIUS server response timeout timer, see AAA configuration in Security Configuration Guide.

· Client timeout timer (supp-timeout)—Starts when the access device sends an EAP-Request/MD5-Challenge packet to a client. If no response is received when this timer expires, the access device retransmits the request to the client.

· Username request timeout timer (tx-period)—Starts when the device sends an EAP-Request/Identity packet to a client in response to an authentication request. If the device does not receive a response before this timer expires, it retransmits the request. The timer also sets the interval at which the network device sends multicast EAP-Request/Identity packets to detect clients that cannot actively request authentication.

· User aging timer (user-aging)—Sets the user aging timer for a type of 802.1X VLAN or VSI.

If you enable 802.1X unauthenticated user aging, you can set a user aging timer for Auth-Fail, critical, or guest VLANs or VSIs. The user aging timer for a type of 802.1X VLAN or VSI determines how long a user can stay in that type of VLAN or VSI.

For more information about how user aging operates, see the usage guidelines for the dot1x unauthenticated-user aging enable command.

Do not set a user aging timer to a multiple of the username request timeout timer (the dot1x timer tx-period command). If you do so, the aging timer will not take effect.

The change to the periodic reauthentication timer applies to the users that have been online only after the old timer expires. Other timer changes take effect immediately on the device.

For the device to take action on 802.1X users as expected, do not set the offline detect timer to the same value as either of the following timers:

· Handshake timer (set by using the dot1x timer handshake-period command).

· Periodic reauthentication timer (set by using the dot1x timer reauth-period command).

Examples

# Set the server timeout timer to 150 seconds.

<Sysname> system-view

[Sysname] dot1x timer server-timeout 150

Related commands

display dot1x

dot1x unauthenticated-user aging enable

retry

timer response-timeout (RADIUS scheme view)

dot1x timer reauth-period

Use dot1x timer reauth-period to set the 802.1X periodic reauthentication timer on a port.

Use undo dot1x timer reauth-period to restore the default.

Syntax

dot1x timer reauth-period reauth-period-value

undo dot1x timer reauth-period

Default

No 802.1X periodic reauthentication timer is configured on a port. The port uses the global 802.1X periodic reauthentication timer.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

reauth-period-value: Sets the 802.1X periodic reauthentication timer in seconds. The value range for the reauth-period-value argument is 60 to 7200.

Usage guidelines

The device reauthenticates online 802.1X users on a port at the specified periodic reauthentication interval when the port is enabled with periodic reauthentication. To enable periodic reauthentication on a port, use the dot1x re-authenticate command.

A change to the periodic reauthentication timer applies to online users only after the old timer expires.

The device selects a periodic reauthentication timer for 802.1X reauthentication in the following order:

1. Server-assigned reauthentication timer.

2. Port-specific reauthentication timer.

3. Global reauthentication timer.

4. Default reauthentication timer.

Examples

# Set the 802.1X periodic reauthentication timer to 60 seconds on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x timer reauth-period 60

Related commands

dot1x timer

dot1x unauthenticated-user aging enable

Use dot1x unauthenticated-user aging enable to 802.1X unauthenticated user aging.

Use undo dot1x unauthenticated-user aging enable to disable 802.1X unauthenticated user aging.

Syntax

dot1x unauthenticated-user aging enable

undo dot1x unauthenticated-user aging enable

Default

User aging is enabled for 802.1X users that have not been authenticated or have not passed authentication.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

802.1X unauthenticated user aging applies to users added to 802.1X guest, critical, or Auth-Fail VLANs or VSIs because they have not been authenticated or have failed authentication.

When a user in one of those VLANs or VSIs ages out, the device removes the user from the VLAN or VSI and deletes the MAC address entry for the user from the access port.

The 802.1X user aging mechanism on a port depends on its access control mode.

· If the port uses port-based access control, a user aging timer starts when the port is assigned to the critical or Auth-Fail VLAN or VSI. When the aging timer expires, the port is removed from the VLAN or VSI and all MAC address entries for users in the VLAN or VSI are also removed.

· If the port uses MAC-based access control, a user aging timer starts for each 802.1X user when they are assigned to the Auth-Fail, critical, or guest VLAN or VSI. When the aging timer for a user expires, the device removes that user from the VLAN or VSI.

For users in one of those VLANs or VSIs on one port to be authenticated successfully and come online on another port, enable this feature. In any other scenarios, disable this feature as a best practice.

The removed users will be unable to access any network resources until after another authentication is triggered.

Examples

# Disable 802.1X unauthenticated user aging on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] undo dot1x unauthenticated-user aging enable

Related commands

dot1x timer

dot1x unicast-trigger

Use dot1x unicast-trigger to enable the 802.1X unicast trigger feature.

Use undo dot1x unicast-trigger to disable the 802.1X unicast trigger feature.

Syntax

dot1x unicast-trigger

undo dot1x unicast-trigger

Default

The 802.1X unicast trigger feature is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

The unicast trigger feature enables the access device to initiate 802.1X authentication when the device receives a data frame from an unknown source MAC address. The device sends a unicast EAP-Request/Identity packet to the unknown source MAC address. It will retransmit the packet if it does not receive any responses within a period of time (set by using the dot1x timer tx-period command). This process continues until the maximum number of request attempts (set by using the dot1x retry command) is reached.

As a best practice, do not use the unicast trigger on a port that performs port-based access control. If you do so, users on the port might fail to come online correctly.

Examples

# Enable the unicast trigger feature on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x unicast-trigger

Related commands

display dot1x

dot1x multicast-trigger

dot1x port-method

dot1x retry

dot1x timer

dot1x user-ip freeze

Use dot1x user-ip freeze to enable 802.1X user IP freezing.

Use undo dot1x user-ip freeze to disable 802.1X user IP freezing.

Syntax

dot1x user-ip freeze

undo dot1x user-ip freeze

Default

802.1X user IP freezing is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This command prevents 802.1X-generated IPSG bindings from being updated because of user IP changes. For information about IP source guard commands, see "IP source guard commands."

Examples

# Enable 802.1X user IP freezing on Twenty-FiveGigE 1/0/1.

<Sysname> system-view

[Sysname] interface twenty-fivegige 1/0/1

[Sysname-Twenty-FiveGigE1/0/1] dot1x user-ip freeze

reset dot1x access-user

Use reset dot1x access-user to log off 802.1X users.

Syntax

reset dot1x access-user [ interface interface-type interface-number | mac mac-address | username username | vlan vlan-id | vsi vsi-name ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

mac mac-address: Specifies an 802.1X user by its MAC address. The mac-address argument is in the format of H-H-H.

username username: Specifies an 802.1X user by its name. The username argument is a case-sensitive string of 1 to 253 characters.

vlan vlan-id: Specifies a VLAN by its VLAN ID. The value range for the vlan-id argument is 1 to 4094.

vsi vsi-name: Specifies a VSI by its name. The vsi-name argument is a case-sensitive string of 1 to 31 characters.

Usage guidelines

Use this command to log off the specified 802.1X users and clear information about these users from the device. These users must perform 802.1X authentication to come online again.

With a VSI specified, this command logs off an 802.1X user if that user has passed authentication and its authorization VSI is the specified VSI.

With a VLAN specified, this command logs off the following 802.1X users:

· Users that have passed 802.1X authentication and have been assigned the specified VLAN as the authorization VLAN by the server.

· Users that stay in the specified VLAN after they have passed 802.1X authentication, because they have not been assigned an authorization VLAN yet.

· Users that are performing 802.1X authentication in the specified VLAN.

To identify the VLAN in which a user is staying, use the display mac-address command.

If you do not specify any parameters, the reset dot1x access-user command logs off all 802.1X users on the device.

Examples

# Log off all 802.1X users on Twenty-FiveGigE 1/0/1.

<Sysname> reset dot1x access-user interface twenty-fivegige 1/0/1

Related commands

display dot1x connection

reset dot1x guest-vlan

Use reset dot1x guest-vlan to remove users from the 802.1X guest VLAN on a port.

Syntax

reset dot1x guest-vlan interface interface-type interface-number [ mac-address mac-address ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

mac-address mac-address: Specifies the MAC address of an 802.1X user in the guest VLAN. If you do not specify this option, the command removes all 802.1X users from the 802.1X guest VLAN on the port.

Examples

# Remove the 802.1X user with MAC address 1-1-1 from the 802.1X guest VLAN on Twenty-FiveGigE 1/0/1.

<Sysname> reset dot1x guest-vlan interface twenty-fivegige 1/0/1 mac-address 1-1-1

Related commands

dot1x guest-vlan

reset dot1x guest-vsi

Use reset dot1x guest-vsi to remove users from the 802.1X guest VSI on a port.

Syntax

reset dot1x guest-vsi interface interface-type interface-number [ mac-address mac-address ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

mac-address mac-address: Specifies the MAC address of an 802.1X user in the guest VSI. If you do not specify this option, the command removes all 802.1X users from the 802.1X guest VSI on the port.

Examples

# Remove the 802.1X user with MAC address 1-1-1 from the 802.1X guest VSI on Twenty-FiveGigE 1/0/1.

<Sysname> reset dot1x guest-vsi interface twenty-fivegige 1/0/1 mac-address 1-1-1

Related commands

dot1x guest-vsi

reset dot1x statistics

Use reset dot1x statistics to clear 802.1X statistics.

Syntax

reset dot1x statistics [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify a port, this command clears 802.1X statistics on all ports.

Examples

# Clear 802.1X statistics on Twenty-FiveGigE 1/0/1.

<Sysname> reset dot1x statistics interface twenty-fivegige 1/0/1

Related commands

display dot1x

09-Security Command Reference

802.1X commands

dot1x auth-fail vlan

dot1x handshake secure

dot1x multicast-trigger

dot1x port-control

dot1x quiet-period

dot1x re-authenticate

dot1x timer

dot1x user-ip freeze

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

Company Information

News & Events

Contact Us

dot1x multicast -trigger